Page 49 - TURNING CATALOG p001-120

P. 49

SLANR/L-TANG HF H HF 16 mm Shank Conﬁguration 93º ISOTURN TOOLS
Screw-Lock Tools Carrying
the LNMX.. Tangentially 3.7° B WF HBH
Clamped Inserts WF SLANR/L 1616M-11S

LH LF LH Right-hand shown

Designation H HF B LF LH WF Insert HBH
100.00 20.0 20.00 LNMX 1104.. 4.0
SLANR/L 1616H-11 TANG 16.0 16.0 16.0 150.00 20.0 16.20 LNMX 1104.. 4.0
125.00 20.0 25.00 LNMX 1104.. 4.0
SLANR/L 1616M-11S TANG 16.0 16.0 16.0 150.00 25.0 30.00 LNMX 1104.. 4.0
125.00 25.0 25.00 LNMX 1506.. 4.0
SLANR/L 2020K-11 TANG 20.0 20.0 20.0 150.00 25.0 30.00 LNMX 1506.. 4.0
170.00 35.0 37.00 LNMX 1506.. 4.0
SLANR/L 2525M-11 TANG 25.0 25.0 25.0 200.00 35.0 45.00 LNMX 1506.. 4.0
170.00 35.0 38.00 LNMX 2210.. 4.0
SLANR/L 2020K-15 TANG 20.0 20.0 20.0 200.00 40.0 47.00 LNMX 2210.. 4.0

SLANR/L 2525M-15 TANG 25.0 25.0 25.0

SLANR/L 3232P-15 TANG 32.0 32.0 32.0

SLANR/L 4040R-15 TANG 40.0 40.0 40.0

SLANR/L 3232P-22 TANG 32.0 32.0 32.0

SLANR/L 4040R-22 TANG 40.0 40.0 40.0

• ap max for facing: LNMX 11-2.8 mm, LNMX 15-3.8 mm, LNMX 22-5.8 mm
For inserts, see pages: LNMX-HM (181) • LNMX-HT (180) • LNMX-WG (181)

The HELITURN system features a unique, double-sided insert The lower forces and smaller loads ensure better tool life,
with 4 cutting edges for Fast Metal Removal (FMR) turning. higher stability and the ability to use very large depths of cut and
HELITURN is a tangentially clamped insert with a unique helical higher feeds.
shaped cutting edge, useful for large depths of cut and higher than The chipformer (with small bumps), deforms and breaks the chip
normal feed rates. into rib type curved segments which can easily be removed from
The LNMX...-HT HELITURN insert is a screw clamped into the the cutting area.
SLANR toolholder and supported by the TLN ..-HT carbide seat. The insert has a frontal clearance angle of 3.7° with a 6° side
This seat has ground surfaces on the top and bottom to ensure clearance angle to enable machining at a 90° shoulder.
perfect contact of the insert with the toolholder. Depths of cut up to 8 mm and facing depths up to 3.2 mm and up
The upper rake face of this insert is mounted level with the to 1.2 mm/rev are achievable with HELITURN.
top of the toolholder to enable chips to flow across the insert The high positive rake angle of these tools allows 10-15% less
without being disturbed by clamps or the toolholder body. power usage than conventional tools with the same parameters.
The 4 curved helical cutting edges ensure positive radial rake By using HELITURN tools, huge cost savings and
angles and soft penetration into the material being cut. profitability in lathe operations are guaranteed.

Spare Parts

Designation TLN 11R/L-HT SR RS4 T-6/5 SR 34-550-C BLD T10/S7 SW6-SD
BLD T10/S7 SW6-SD
SLANL 1616H-11 TANG TLN 11R/L-HT SR RS4 T-6/5 SR 34-550-C BLD T10/S7 SW6-SD
SLANL 1616M-11S TANG BLD T10/S7 SW6-SD
SLANR 1616H-11 TANG TLN 11R/L-HT SR RS4 T-6/5 SR 34-550-C BLD T10/S7 SW6-SD
SLANR 1616M-11S TANG BLD T10/S7 SW6-SD
SLANL 2020K-11 TANG TLN 11R/L-HT SR RS4 T-6/5 SR 34-550-C BLD T10/S7 SW6-SD
SLANR 2020K-11 TANG BLD T10/S7 SW6-SD
SLANL 2525M-11 TANG TLN 11R/L-HT SR RS4 T-6/5 SR 34-550-C BLD T15/S7
SLANR 2525M-11 TANG BLD T15/S7
SLANL 2020K-15 TANG TLN 11R/L-HT SR RS4 T-6/5 SR 34-550-C BLD T15/S7
SLANR 2020K-15 TANG BLD T15/S7
SLANL 2525M-15 TANG TLN 11R/L-HT SR RS4 T-6/5 SR 34-550-C BLD T15/S7
SLANR 2525M-15 TANG BLD T15/S7
SLANL 3232P-15 TANG TLN 11R/L-HT SR RS4 T-6/5 SR 34-550-C BLD T15/S7
SLANR 3232P-15 TANG BLD T15/S7
SLANL 4040R-15 TANG TLN 15R/L-HT SR RS4 T-6/5 SR 34-535-SN BLD T20/S7 SW6-T-SH
SLANR 4040R-15 TANG BLD T20/S7 SW6-T-SH
SLANL 3232P-22 TANG TLN 15R/L-HT SR RS4 T-6/5 SR 34-535-SN BLD T20/S7 SW6-T-SH
SLANR 3232P-22 TANG BLD T20/S7 SW6-T-SH
SLANL 4040R-22 TANG TLN 15R/L-HT SR RS4 T-6/5 SR 34-535-SN SW6-T-SH
SLANR 4040R-22 TANG SW6-T-SH
TLN 15R/L-HT SR RS4 T-6/5 SR 34-535-SN SW6-T-SH
SW6-T-SH
TLN 15R/L-HT SR RS4 T-6/5 SR 34-535-SN SW6-T-SH
SW6-T-SH
TLN 15R/L-HT SR RS4 T-6/5 SR 34-535-SN SW6-T-SH
SW6-T-SH
TLN 15R/L-HT SR RS4 T-6/5 SR 34-535-SN

TLN 15R/L-HT SR RS4 T-6/5 SR 34-535-SN

TLN 22R/L-HT SR 10500401 T-7/5 SR 14-591/L-SN

44 45 46 47 48 49 50 51 52 53 54