Page 48 - Turning_catalog_INCH_2022_45_P1-112
P. 48
ISOTURN TOOLS Designation 1.000 .625 WF 3.7° 1.000 LF 4.000 H HF 1.000 .625” shank configuration -6.0 93 º LNMX 11
SLANR/L-TANG
HF
Screw-Lock Tools Carrying
the LNMX.. Tangentially
.157 Ref.
Clamped Inserts
B
LH
B
Insert
H
HF
WF
GAMP
LH
LF
GAMF
SLANR/L 10-11 TANG
.625
.625
.790
-6.0
.750
SLANR 12-11 TANG
.750
-6.0
-6.0
.750
1.000
LNMX 11
4.500
.750
SLANR/L 16-11 TANG
LNMX 11
1.250
1.000
1.000
-6.0
6.000
-6.0
SLANR 12-15 TANG
.750
.750
.980
1.000
-6.0
6.000
LNMX 15
SLANR/L 16-15 TANG
1.180
-6.0
1.250
1.250
6.000
-6.0
-6.0
LNMX 15
SLANR/L 20-15 TANG
1.460
1.370
1.250
-6.0
LNMX 15
1.700
7.000
1.380
-6.0
1.500
1.500
1.500
SLANR/L 24-15 TANG 1.000 .750 1.000 4.500 1.000 1.000 -6.0 -6.0 LNMX 15
SLANR/L 20-22 TANG 1.250 1.250 1.250 6.000 1.380 1.500 -6.0 -6.0 LNMX 22
SLANR/L 24-22 TANG 1.500 1.500 1.500 7.000 1.500 1.780 -6.0 -6.0 LNMX 22
• ap max for facing: LNMX 11-.110", LNMX 15-.150", LNMX 22-.228"
For inserts, see pages: LNMX-HM (174) • LNMX-HT (173) • LNMX-WG (174)
The HELITURN system features a unique, double-sided insert with The lower forces and smaller loads ensure better tool life, higher stability
4 cutting edges for Fast Metal Removal (FMR) turning. and the ability to use very large depths of cut and higher feeds.
The HELITURN is a tangentially clamped insert with The chipformer (with small bumps), deforms and breaks the chip into rib
a unique helical shaped cutting edge, useful for large type curved segments which can easily be removed from the cutting area.
depths of cut and higher than normal feed rate. The insert has a frontal clearance angle of 3.7° with a 6° side
The LNMX...-HT HELITURN insert is screw-clamped into the clearance angle to allow machining to a 90° shoulder.
SLANR toolholder and supported by the TLN ..-HT carbide Depths of cut up to .315” and facing depths to .126” at
seat. This seat has ground surfaces on the top and bottom, up to .047 IPR are achievable with HELITURN.
to ensure perfect contact of the insert with the toolholder. The high positive rake angle of these tools allows 10-15% less
The upper rake face of this insert is mounted level with the top of the power usage than conventional tools at the same parameters.
toolholder to enable chips to flow across the insert, without being disturbed By using HELITURN tools, huge cost savings and
by clamps or the toolholder body. The 4 curved helical cutting edges ensure profitability in lathe operations are guaranteed.
positive radial rake angles and soft penetration into the material being cut.
Spare Parts
Designation
SLANL 10-11 TANG TLN 11R/L-HT SR RS4 T-6/5 SR 34-550-C BLD T10/S7 SW6-SD
SLANR 10-11 TANG TLN 11R/L-HT SR RS4 T-6/5 SR 34-550-C BLD T10/S7 SW6-SD
SLANR 12-11 TANG TLN 11R/L-HT SR RS4 T-6/5 SR 34-550-C BLD T10/S7 SW6-SD
SLANL 16-11 TANG TLN 11R/L-HT SR RS4 T-6/5 SR 34-550-C BLD T10/S7 SW6-SD
SLANR 16-11 TANG TLN 11R-HT SR RS4 T-6/5 SR 34-550-C BLD T10/S7 SW6-SD
SLANR 12-15 TANG TLN 15R/L-HT SR RS4 T-6/5 SR 34-535-SN BLD T15/S7 SW6-T-SH
SLANL 16-15 TANG TLN 15R/L-HT SR RS4 T-6/5 SR 34-535-SN BLD T15/S7 SW6-T-SH
SLANR 16-15 TANG TLN 15R/L-HT SR RS4 T-6/5 SR 34-535-SN BLD T15/S7 SW6-T-SH
SLANL 20-15 TANG TLN 15R/L-HT SR RS4 T-6/5 SR 34-535-SN BLD T15/S7 SW6-T-SH
SLANR 20-15 TANG TLN 15R/L-HT SR RS4 T-6/5 SR 34-535-SN BLD T15/S7 SW6-T-SH
SLANL 24-15 TANG TLN 15R/L-HT SR RS4 T-6/5 SR 34-535-SN BLD T15/S7 SW6-T-SH
SLANR 24-15 TANG TLN 15R-HT SR RS4 T-6/5 SR 34-535-SN BLD T15/S7 SW6-T-SH
SLANL 20-22 TANG TLN 22R/L-HT SR 10500401 T-7/5 SR 14-591/L-SN BLD T20/S7 SW6-T-SH
SLANR 20-22 TANG TLN 22R/L-HT SR 10500401 T-7/5 SR 14-591/L-SN BLD T20/S7 SW6-T-SH
SLANL 24-22 TANG TLN 22R/L-HT SR 10500401 T-7/5 SR 14-591/L-SN BLD T20/S7 SW6-T-SH
SLANR 24-22 TANG TLN 22R/L-HT SR 10500401 T-7/5 SR 14-591/L-SN BLD T20/S7 SW6-T-SH
46 ISCAR