Page 17 - Turning_catalog_INCH_2022_45_P509-690

CDX LH
DGTR/L-B-T-SH
Reinforced Parting and Grooving H H OAH
Short Head Tools Carrying PARTING
DGN Double-Ended Inserts CUTDIA WB
OAL
CWN-CWX WF B
Left-hand shown

Designation CWN (1) CWX (2) H B WB WF OAL LH CUTDIA CDX (3) OAH
DGTR/L 2009B-1.5T9SH .039 .059 .787 .354 .047 .331 3.937 .748 3.740 .354 .93 SR 16-236 P T-15/5
• Important: .055" (1.4 mm) width inserts should be used only on tools for .055" specific width! • For user guide, see pages 594-603
(1) Minimum cutting width
(2) Maximum cutting width
(3) Cutting depth maximum
For inserts, see pages: DGN-P (539) • DGN/DGNM-J/JS/JT (535) • DGR-P (540) • DGR/L-J/JS (536)

LH LH

DGTR/L HBH
Integral Shank Parting H HF
and Grooving Tools WB CUTDIA LH
B CWN-CWX
OAL
Right-hand shown
Designation CWN (1) CWX (2) H B WB OAL LH HBH CUTDIA Insert
DGTR/L 9.5-2 .075 .100 .375 .375 .071 4.500 1.100 .26 1.400 DG. 1.../DG. 2.. EDG 33B*
DGTR/L 12.7-2 .075 .100 .500 .500 .071 4.500 1.100 .26 1.400 DG. 1.../DG. 2.. EDG 33B*
DGTR/L 1616-2 .075 .098 .630 .630 .071 5.906 1.142 .10 1.378 DG. 1.../DG. 2.. EDG 33B*
DGTR/L 19-2 .075 .100 .750 .750 .071 4.500 1.100 .14 1.400 DG. 1.../DG. 2.. EDG 33A*
DGTR/L 12.7-3 .118 .125 .500 .500 .100 4.500 1.100 .26 1.400 (3) DG. 1.../DG. 3.. EDG 33B*
DGTR/L 1616-3 .118 .125 .630 .630 .098 5.906 1.142 .26 1.378 DG. 1.../DG. 3.. EDG 33B*
(3)
DGTR/L 19-3 .118 .125 .750 .750 .100 4.500 1.100 - 1.400 DG. 1.../DG. 3.. EDG 33A*
(3)
DGTR/L 25.4-3 .118 .125 1.000 1.000 .100 6.000 1.100 - 1.400 DG. 1.../DG. 3.. EDG 33A*
(3)
DGTR/L 19-4 .157 .157 .750 .750 .134 4.500 1.200 - 2.000 DG. 4.../GRIP 4.. EDG 33A*
DGTR/L 25.4-4 .157 .157 1.000 1.000 .134 6.000 1.200 - 2.000 DG. 4.../GRIP 4.. EDG 33A*
DGTR/L 25.4-5 .189 .200 1.000 1.000 .157 6.000 1.300 - 3.000 DG. 5.../GRIP 5.. EDG 33A*
DGTR/L 25.4-6 .236 .236 1.000 1.000 .209 6.000 1.300 - 3.000 DG. 6.../GRIP 6.. EDG 33A*
• Insert limit is Tmax=.709". If deeper penetration is required, the insert should be modified into single-ended by the user
• DG..1.0 insert can be mounted into pocket sizes 2 and 3, in which case the pocket width has to be modified - see page 531
• For user guide, see pages 594-603
(1) Minimum cutting width
(2) Maximum cutting width
(3) Dmax=1.69" when single-ended insert is used
* Optional, should be ordered separately
For inserts, see pages: GRIPA (278) • GRIPA (full radius) (279) • DGN-LF/LFT (537) • DGN-MF (537) • DGN/DGNC/DGNM-C (533)
• DGR/L-C DGRC/LC-C (534) • DGN/DGNM-J/JS/JT (535) • DGR/L-J/JS (536) • DGN-P (539) • DGN-UT/UA (539) • DGN-W (534) • DGN-WP (540)
• DGN-Z (538) • DGR-P (540) • DGR-WP (541) • DGR-Z/ZS (538) • GRIP (277) • GRIP (full radius) (278)

525