Page 32 - MILLING_CATALOG_INCH_2022_P229-P360

FACE MILLS IQ845 FSY-R05 DCONMS APMX OAL
DHUB
50° Face Mills Carrying Square
Inserts with 8 Cutting Edges

50°
DC
DCX

Designation
DC
IQ845 FSYD1.5-04-0.75-R05
.750
1.500
.100
1.730
.50
1.500
A
4
IQ845 FSYD1.5-07-0.75-R05 1.500 DCX (1) CICT (2) APMX OAL DCONMS Arbor (3) DHUB Lbs
1.730
1.500
A
.750
1.500
1.500
7
.100
.46
IQ845 FSYD2.0-05-0.75-R05 2.000 2.230 5 .100 1.750 .750 A 1.750 1.21
IQ845 FSYD2.0-09-0.75-R05 2.000 2.230 9 .100 1.750 .750 A 1.750 1.43
IQ845 FSYD2.5-07-1.00-R05 2.500 2.730 7 .100 1.750 1.000 B 2.250 1.87
IQ845 FSYD2.5-11-1.00-R05 2.500 2.730 11 .100 1.750 1.000 B 2.250 1.98
• For user guide, see pages 586-591
(1) Cutting diameter maximum
(2) Number of inserts
(3) For adaptation options, see page 592
For inserts, see pages: IQ845 SYHU-05 (540)

Spare Parts
Designation
IQ845 FSYD1.5-04-0.75-R05 SR M2.5X6-T7-60 T-7/51 SR UNF 3/8X1 B18.3
IQ845 FSYD1.5-07-0.75-R05 SR M2.5X6-T7-60 T-7/51 SR UNF 3/8X1 B18.3
IQ845 FSYD2.0-05-0.75-R05 SR M2.5X6-T7-60 T-7/51 SR UNF 3/8X1 B18.3
IQ845 FSYD2.0-09-0.75-R05 SR M2.5X6-T7-60 T-7/51 SR UNF 3/8X1 B18.3
IQ845 FSYD2.5-07-1.00-R05 SR M2.5X6-T7-60 T-7/51
IQ845 FSYD2.5-11-1.00-R05 SR M2.5X6-T7-60 T-7/51
DHUB
F45WG DCONMS
45° Face Mills Carrying
Octagonal ONHU/MU 0806... OAL
Inserts with 16 Cutting Edges 44.3°
DC APMX
DCX
Designation DC DCX (2) CICT (3) APMX OAL DHUB DCONMS Arbor (4) Lbs
F45WG D3.0-10-1.0-FX-R08 (1) 3.000 3.470 10 .220 1.750 2.210 1.000 B 1.90
F45WG D4.0-14-1.5-FX-R08 (1) 4.000 4.470 14 .220 2.000 3.270 1.500 B 3.94
F45WG D5.0-18-1.5-FX-R08 (1) 5.000 5.470 18 .220 2.000 3.270 1.500 B 5.65
• Note: Recommended wedge clamping torque: 75-80 lbfxinch • For user guide see pages 586-591
(1) For internal coolant through the holder, use a matching coolant set (should be ordered separately)
(2) Cutting diameter maximum
(3) Number of inserts
(4) For adaptation options, see page 592
For inserts, see pages: ONHQ-TN (557) • ONHU 0806-N-PL (557) • ONHU 0806AN-W (558) • ONHU/ONMU 080608 AN-N-HP (558) • ONHU/ONMU-08-TN-MM (557) •
ONHU/ONMU-08-TN/HL (556)
Wiper Inserts Mounting of Wiper Insert on
Wiper inserts are used on face mill cutters, provide improved Face Mills
surface finish and eliminate the use of other finishing cutters. W2 W2
ONHU 0806AN-14R-W, mounted on F45WG and F45NM ONHU 0806AN-14R-W
milling cutters. This insert provides 4 right-hand wiper edges. W1
W1

Mounting instructions have been included in each insert W2 W2 W1
package, in order avoid incorrect clamping orientation. W1
Only correct mounting will provide high surface finish!

Spare Parts
Designation
F45WG SR 118-069 BLD IP20/S7 SW6-T LW 35-475/M

260 ISCAR