Page 106 - Turning_catalog_INCH_2022_45_P509-690

FACE GROOVING HGHR/L-3 CW CDX CDX .375 .375 HBH WF CDX CW LH .63 OAL .370 H B OAH OAH 5.000 .750 SR 76-1400 T-20/3

Integral Holders for Face
DAXN-DAXX
HBH
Grooving and Turning
OAW
Right-hand shown

(1)
(2)
WF
OAW
Designation
B
H
DAXX
DAXN
LH
OAL
HGHL 9.5-12-3T6
.236
.118
.67
.12
.47
.559
HGHL 12.7-12-3T6
.236
SR 76-1400
.118
.63
.47
.12
.460
.646
.500
.500
5.000
.750
T-20/3
.70
HGHL 12.7-16-3T6
.460
.619
.236
.625
.625
T-20/3
.12
.118
.750
.82
.590
.771
.63
HGHR/L 15.9-12-3T6
.47
SR 76-1400
5.000
5.000
T-20/3
.907
.750
-
.47
SR 76-1400
.63
.95
.750
.750
.236
.118
HGHR/L 19-12-3T6
.750
SR 76-1400
.750
.118
-
5.000
.63
.750
.907
.236
T-20/3
.750
.98
HGHR/L 19-16-3T6
.750
.95
.63
1.20
HGHR/L 25.4-12-3T6 .118 .236 .500 .500 .12 .63 .98 1.000 .70 1.157 5.000 .750 SR 76-1400 T-20/3
.47
1.000
.236
T-20/3
1.000
SR 76-1400
.750
5.000
.118
-
HGHR/L 25.4-16-3T6 .118 .236 1.000 1.000 - .63 .98 1.000 1.20 1.157 5.000 .750 SR 76-1400 T-20/3
HGHR 9.5-16-3T6 .118 .236 .375 .375 .12 .63 .98 .370 .67 .524 5.000 .750 SR 76-1400 T-20/3
HGHR 15.9-16-3T6 .118 .236 .625 .625 .12 .63 .98 .590 .82 .735 5.000 .750 SR 76-1400 T-20/3
• HGN & GRIP inserts can be used only with right-hand toolholders, HGPL inserts only with left-hand toolholders • For user guide, see pages 607-612, 663-669
(1) Minimum penetration diameter
(2) Maximum penetration diameter
For inserts, see pages: GRIP (277) • GRIP (full radius) (278) • HGN-C (541) • HGN-J (542) • HGN-UT (542) • HGPL (631)
Groove can be widened with no limitation toward or away
from the center with the exception of the following tools: d
HGHR/L...-12-3T6
D d
.472 .157 Limitation of widening toward center
.512 .039 depends on the major diameter (D) as D
.513 0 per chart

LH
HFHR/L-3T
Integral Toolholders for CDX HFHR/L --3T12 H H OAH
External Facing WF2 CW
DAXN-DAXX
CDX WF B
.83
OAL Right-hand shown
Designation CW CDX H B OAL WF WF2 DAXN (2) DAXX (3) LH OAH
HFHR/L 25.4-25-3T12 .118 .470 1.000 1.000 6.000 1.020 .21 .98 1.18 1.500 1.31 SR M6X16 DIN912 HW 5.0
HFHR/L 25.4-30-3T12 .118 .470 1.000 1.000 6.000 1.020 .21 1.18 1.50 1.500 1.35 SR M6X16 DIN912 HW 5.0
HFHR/L 25.4-38-3T12 .118 .470 1.000 1.000 6.000 1.020 .21 1.50 1.89 1.500 1.39 SR M6X16 DIN912 HW 5.0
HFHR/L 25.4-48-3T22 (1) .118 .870 1.000 1.000 6.000 1.020 - 1.89 2.36 1.570 1.43 SR M6X16 DIN912 HW 5.0
HFHR/L 25.4-60-3T22 (1) .118 .870 1.000 1.000 6.000 1.020 - 2.36 2.96 1.570 1.43 SR M6X16 DIN912 HW 5.0
HFHR/L 25.4-75-3T25 (1) .118 .980 1.000 1.000 6.000 1.020 - 2.95 3.94 1.690 1.43 SR M6X16 DIN912 HW 5.0
• For user guide, see pages 607-612, 663-669
(1) For deep face grooving only
(2) Minimum penetration diameter
(3) Maximum penetration diameter
For inserts, see pages: HFPR/L (629) • HFPR/L (full radius) (629)
Groove can be widened with no limitation toward or away d
from the center with the exception of the following tools:
HFHR/L-#-25-3T12
D d
.98 .20 Limitation of widening toward D
1.02 .08 center (d) depends on the major
≥1.06 0 diameter (D) as per chart

614 ISCAR