Page 107 - ISCAR FACE GROOVING LINES
P. 107
GIPA/GIDA 8 (full radius) ±0.025 IC2030 Ref.
Precision Double-Ended 7° IC4
Inserts with Polished Top Rake 10° ID5 6.4
for Machining Aluminum GIDA 80-40CB
CW FACE GROOVE-TURNGIDA 80-40
RE BW GIPA 8.00-4.00
METRIC
Dimensions Tough 1 Hard Recommended Machining Data
Designation CW RE CWTOL(2) RETOL(3) BW ap f turn f groove
8.00 4.00 0.02 0.050 5.60 • •
GIDA 80-40 8.00 4.00 0.02 0.050 5.60 • (mm) (mm/rev) (mm/rev)
GIDA 80-40-D 8.00 • 0.00-4.00 0.24-0.67 0.14-0.38
GIDA 80-40CB-D (1) 8.00 4.00 0.02 0.050 5.60 • 0.00-4.00 0.24-0.67 0.14-0.38
GIDA 80-40YZ 8.00 0.00-4.00 0.24-0.67 0.14-0.38
GIDA 80-40YZ-D 8.00 4.00 0.02 0.050 5.60 • • 0.00-4.00 0.24-0.67 0.14-0.38
GIPA 8.00-4.00 4.00 0.02 0.050 5.60 0.00-4.00 0.35-0.96 0.18-0.48
0.00-4.00 0.24-0.67 0.14-0.38
4.00 0.02 0.050 6.00 •
• ID5 is a single-ended PCD tipped insert • For cutting speed recommendations and user guide, see pages 161-173
(1) Should not be clamped on tools with "A" suffix
(2) Cutting width tolerance (+/-)
(3) Corner radius tolerance (+/-)
For tools, see pages: • GAFG-R/L-8 (87) • GHFGR/L-8 (84)
±.001 1.18 Ref.
GIPA/GIDA 8 (full radius) 10° 7° .252
Precision Double-Ended GIDA 80-40CB
Inserts with Polished Top Rake CW GIDA 80-40
for Machining Aluminum RE BW GIPA 8.00-4.00
INCH
Dimensions Tough 1 Hard Recommended Machining Data
CWTOL(2) RETOL(3) IC20 ap f turn f groove
.0008 .0020 IC4
.0008 .0020 ID5 (inch) (IPR) (IPR)
Designation CW RE .0008 .0020 BW .000-.157 .0094-.0264 .0055-.0150
.315 .1575 .0008 .0020 • .000-.157 .0094-.0264 .0055-.0150
GIDA 80-40 .315 .1575 .0008 .0020 .220 • • • .000-.157 .0094-.0264 .0055-.0150
GIDA 80-40-D .315 .1575 .0008 .0020 • .000-.157 .0094-.0264 .0055-.0150
GIDA 80-40CB-D (1) .315 .1575 .220 .000-.157 .0138-.0378 .0071-.0189
GIDA 80-40YZ .315 .1575 .220 .000-.157 .0094-.0264 .0055-.0150
GIDA 80-40YZ-D .315 .1575
GIPA 8.00-4.00 .220 • •
.220
.236 •
• ID5 is a single-ended PCD tipped insert • For cutting speed recommendations and user guide, see pages 161-173
(1) Should not be clamped on tools with "A" suffix
(2) Cutting width tolerance (+/-)
(3) Corner radius tolerance (+/-)
For tools, see pages: • GAFG-R/L-8 (87)
105
