Page 123 - ISCAR FACE GROOVING LINES

GFF-R/L CDX 7° FACE GROOVE-TURN
Face Grooving Inserts DAXN
CW
RE RL

METRIC Tough 1 Hard Recommended
Dimensions Machining Data
••
Designation CW RE CWTOL(1) RETOL(2) DAXN(3) DAXX(4) •IC354 f face-groove
2.10 0.20 0.10 0.050 25.0 36.0 IC20 (mm/rev)
GFF 2R 3.00 0.30 0.10 0.050 30.0 55.0 •• 0.03-0.13
GFF 3L 3.00 0.30 0.10 0.050 30.0 55.0 0.03-0.15
GFF 3R 0.03-0.15

INC H

Dimensions Tough 1 Hard Recommended
Machining Data
Designation CW RE CWTOL(1) RETOL(2) DAXN(3) DAXX(4) IC354••
.083 .008 .0039 .0020 .98 1.42 IC20• f face-groove
GFF 2R .118 .012 .0039 .0020 1.18 2.17 (IPR)
GFF 3L .118 .012 .0039 .0020 1.18 2.17 ••
GFF 3R .0012-.0051
.0012-.0059
.0012-.0059

(1) Cutting width tolerance (+/-)
(2) Corner radius tolerance (+/-)
(3) Minimum axial grooving diameter
(4) Maximum axial grooving diameter
For tools, see pages: SGFFA (117) • SGFFR/L (115)

GFF-N CDX 7° N
Face Grooving Inserts DAXN RE

CW

METRIC Tough 1 Hard Recommended
Dimensions Machining Data
••
Designation CW RE CWTOL(1) RETOL(2) DAXN(3) IC354•• f face-groove
35.0 IC20•• (mm/rev)
GFF 2N 54.0 •• 0.03-0.13
GFF 3N 2.10 0.20 0.10 0.050 35.0 •• 0.03-0.15
GFF 4N 40.0 0.04-0.18
GFF 5N 3.00 0.30 0.10 0.050 44.0 0.05-0.18
GFF 6N 0.05-0.20
4.00 0.25 0.10 0.050 DAXN(3)
1.38
5.00 0.25 0.10 0.050 2.13
1.38
6.00 0.25 0.10 0.050 1.57
1.73
INCH

Dimensions Tough 1 Hard Recommended
Machining Data
Designation CW RE CWTOL(1) RETOL(2) ••IC354
•• IC20 f face-groove
.0039 .0020 •• (IPR)
GFF 2N .083 .008 .0039 .0020 ••
GFF 3N .118 .012 .0039 .0020 •• .0012-.0051
.157 .010 .0039 .0020 .0012-.0059
GFF 4N .197 .010 .0039 .0020 .0016-.0071
.236 .010 .0020-.0071
GFF 5N .0020-.0079
GFF 6N

• Grooving depth is limited only by the tool being used
(1) Cutting width tolerance (+/-)
(2) Corner radius tolerance (+/-)
(3) Minimum axial grooving diameter
For tools, see pages: SGFFA (117) • SGFFH (119) • SGFFR/L (115)

121