Page 117 - TURNING CATALOG p255-458

SCIR/L-41-AR/AL 8.5 HF Workpiece TOOLS FOR MINIATURE PARTS
Turning Inserts with a 41 4 GAN Tc
Frontal Relief Angle Dimensions
Tc CDX Recommended Machining Data
CW

8° Sharp corner

IC1008 ap f turn

Designation CW HF(1) CDX Tc GAN (mm) (mm/rev)
16.0 • 0.05-4.00 0.02-0.15
SCIL 41-AL00-33K16 3.30 0.5 4.00 11.0 16.0 • 0.05-4.00 0.02-0.15

SCIR 41-AR00-33K16 3.30 0.5 4.00 11.0

(1) Cutting edge below center

For tools, see pages: SCHR/L-41BF (369)

SCIR/L-41-N/R/L 4 41 GAN HF Workpiece
Grooving and Parting Inserts 8.5
Tc 15° CDX Tc
SCIR 41-...R15K..
CDX CW Right-hand shown
SCIR 41-...N-K00 Sharp corner x 2
Recommended
Dimensions Machining Data

Designation CW CWTOL(1) GAN HF(2) CDX Tc IC1008 f groove
0.020 (mm/rev)
SCIL 41-100L15K00 1.00 0.020 0.0 0.2 6.00 11.0
SCIR/L 41-100N-K00 1.00 0.020 • 0.02-0.04
1.00 0.020 0.0 0.1 6.15 11.0 • 0.03-0.05
SCIR 41-100R15K00 0.020 • 0.02-0.04
0.020 0.0 0.2 6.00 11.0 • 0.03-0.06
0.020 • 0.03-0.07
SCIL 41-150L15K00 1.50 0.020 0.0 0.2 8.00 11.0 • 0.03-0.06
SCIR/L 41-150N-K00 1.50 0.020 • 0.03-0.06
SCIR 41-150R15K00 1.50 0.020 0.0 0.1 8.15 11.0 • 0.03-0.06
SCIL 41-150L15K7 1.50 0.020 • 0.03-0.07
SCIR 41-150R15K7 1.50 0.020 0.0 0.2 8.00 11.0 • 0.03-0.09
0.020 • 0.03-0.07
0.020 7.0 0.5 8.00 11.0 • 0.03-0.07
0.020 • 0.03-0.07
0.020 7.0 0.5 8.00 11.0 • 0.03-0.07
0.020 • 0.03-0.09
SCIL 41-200L15K00 2.00 0.020 0.0 0.2 10.00 11.0 • 0.03-0.07
SCIR/L 41-200N-K00 2.00 0.020 • 0.03-0.07
SCIR 41-200R15K00 2.00 0.020 0.0 0.1 11.00 11.0 • 0.03-0.07
SCIL 41-200L15K7 2.00 0.020 • 0.03-0.08
SCIR 41-200R15K7 2.00 0.0 0.2 10.00 11.0 • 0.03-0.10
• 0.03-0.08
7.0 0.5 10.00 11.0

7.0 0.5 10.00 11.0

SCIL 41-250L15K00 2.50 0.0 0.2 10.00 11.0
SCIR/L 41-250N-K00 2.50
SCIR 41-250R15K00 2.50 0.0 0.1 11.00 11.0
SCIL 41-250L15K7 2.50
SCIR 41-250R15K7 2.50 0.0 0.2 10.00 11.0

7.0 0.5 10.00 11.0

7.0 0.5 10.00 11.0

SCIL 41-300L15K00 3.00 0.0 0.2 10.00 11.0
3.00
SCIR/L 41-300N-K00 3.00 0.0 0.1 11.00 11.0
SCIR 41-300R15K00
0.0 0.2 10.00 11.0

(1) Cutting width tolerance (+/-)

(2) Cutting edge below center

For tools, see pages: SCHR/L-41BF (369)

371