Page 30 - FAST_FEED_MILL_Brochure_INCH_2022
P. 30
DHUB
FFQ8-12 DCONMS
Fast Feed Face Mills Carrying Rd°
Double-Sided Inserts OAL APMX
with 8 Cutting Edges
12˚
DC
DCX
Designation DC DCX (1) APMX CICT (2) OAL DHUB DCONMS Arbor RMPX° (3) MDN (4) MDX (5) TQ (6) MIID (7) Lbs
FFQ8 D2.00-05-0.75-12 1.236 2.000 .0600 5 1.625 1.850 .750 A .3 3.236 3.960 42.50 FFQ8 SZMU 120520 1.61
FFQ8 D2.50-06-1.00-12 1.736 2.500 .0600 6 1.750 2.250 1.000 A .2 4.236 4.960 42.50 FFQ8 SZMU 120520 1.94
FFQ8 D3.00-07-1.00-12 2.236 3.000 .0600 7 1.750 2.250 1.000 A .2 5.236 5.960 42.50 FFQ8 SZMU 120520 3.64
FFQ8 D4.00-08-1.50-12 3.236 4.000 .0600 8 2.000 3.230 1.500 B .1 7.236 7.960 42.50 FFQ8 SZMU 120520 6.17
• Radius for programming .142" • To generate a straight surface without cusps, the width of cut most not exceed DC • For slot milling or machining with high tool
overhang, the maximum depth of cut should be reduced by 30%
(1) Cutting diameter maximum
(2) Number of inserts
(3) Maximum ramping angle
(4) Machinable diameter minimum for interpolation
(5) Machinable diameter maximum for interpolation
(6) Recommended tightening torque (lbfxin) for insert screw
(7) Master insert identification
Spare Parts
Designation
FFQ8 D2.00-05-0.75-12 SR M4X0.7-L11.5 IP15 BLD IP15/S7 SW6-T-SH SR UNF 3/8X1 B18.3
FFQ8 D2.50-06-1.00-12 SR M4X0.7-L11.5 IP15 BLD IP15/S7 SW6-T-SH SR UNF 1/2X20X1 B18.3
FFQ8 D3.00-07-1.00-12 SR M4X0.7-L11.5 IP15 BLD IP15/S7 SW6-T-SH SR UNF 1/2X20X1 B18.3
FFQ8 D4.00-08-1.50-12 SR M4X0.7-L11.5 IP15 BLD IP15/M7 SW6-T-SH
DHUB
MFQ8-12 DCONMS
Moderate Feed Face Mills
Carrying Double-Sided Inserts OAL APMX
with 8 Cutting Edges
22˚
DC
DCX
Designation DC DCX (1) APMX CICT (2) OAL DHUB DCONMS Arbor TQ (3) MIID (4) Lbs
MFQ8 D2.00-05-0.75-12 1.276 2.000 .1180 5 1.625 1.850 .750 A 42.50 FFQ8 SZMU 120520 1.48
MFQ8 D2.50-06-1.00-12 1.776 2.500 .1180 6 1.750 2.250 1.000 A 42.50 FFQ8 SZMU 120520 2.43
MFQ8 D3.00-07-1.00-12 2.276 3.000 .1180 7 1.750 2.250 1.000 A 42.50 FFQ8 SZMU 120520 3.38
MFQ8 D4.00-08-1.50-12 3.276 4.000 .1180 8 2.000 3.230 1.500 B 42.50 FFQ8 SZMU 120520 4.41
• Radius for programming .197" • To generate a straight surface without cusps, the width of cut most not exceed DC • For slot milling or machining with high tool
overhang, the maximum depth of cut should be reduced by 30%
(1) Cutting diameter maximum
(2) Number of inserts
(3) Recommended tightening torque (lbfxin) for insert screw
(4) Master insert identification
Spare Parts
Designation
MFQ8 D2.00-05-0.75-12 SR M4X0.7-L11.5 IP15 BLD IP15/S7 SW6-T-SH SR UNF 3/8X1 B18.3
MFQ8 D2.50-06-1.00-12 SR M4X0.7-L11.5 IP15 BLD IP15/S7 SW6-T-SH SR UNF 1/2X20X1 B18.3
MFQ8 D3.00-07-1.00-12 SR M4X0.7-L11.5 IP15 BLD IP15/S7 SW6-T-SH SR UNF 1/2X20X1 B18.3
MFQ8 D4.00-08-1.50-12 SR M4X0.7-L11.5 IP15 BLD IP15/M7 SW6-T-SH
30 FAST FEED MILLING
