Page 22 - Solid_Brochure_2021_INCH
P. 22
Slotting Cutting Diameter Feed (IPT) Slotting
Axial
Material No. Cutting Speed Recommendations (Vc) SFM Hardness HB
ISO Material Condition 1/8 3/16 1/4 5/16 3/8 7/16 1/2 5/8 3/4 1 ap max
1 Non-alloy Annealed 740-800 125 .0003 .0004 .0006 .0007 .0009 .0010 .0012 .0015 .0018 .0024 1xD
2 steel and <.25%C Annealed 590-680 190 .0003 .0004 .0006 .0007 .0009 .0010 .0012 .0015 .0018 .0024 1xD
3 cast steel, Quench and tempered 475-650 250 .0003 .0004 .0006 .0007 .0009 .0010 .0012 .0015 .0018 .0024 1xD
4 free cutting >=.55%C Annealed 475-650 220 .0003 .0004 .0006 .0007 .0009 .0010 .0012 .0015 .0018 .0024 1xD
5 steel >=.55%C Quenched & tempered 420-530 300 .0003 .0004 .0006 .0007 .0009 .0010 .0012 .0015 .0018 .0024 1xD
6 Annealed 475-650 200 .0003 .0004 .0006 .0007 .0009 .0010 .0012 .0015 .0018 .0024 1xD
Low alloy & cast
7 Quenched & tempered 355-530 275 .0003 .0004 .0006 .0007 .0009 .0010 .0012 .0015 .0018 .0024 1xD
P steel (less than 5% of
8 alloying elements) Quenched & tempered 380-530 300 .0003 .0004 .0006 .0007 .0009 .0010 .0012 .0015 .0018 .0024 1xD
9 Quenched & tempered 415-530 350 .0003 .0004 .0006 .0007 .0009 .0010 .0012 .0015 .0018 .0024 1xD
10 High alloyed steel, Annealed 380-530 200 .0003 .0004 .0006 .0007 .0009 .0010 .0012 .0015 .0018 .0024 1xD
11 cast steel and tool steel Quenched & tempered 200-360 325 .0003 .0004 .0006 .0007 .0009 .0010 .0012 .0015 .0018 .0024 1xD
12 Stainless steel Ferritic/martensitic 230-475 200 .0003 .0004 .0006 .0007 .0009 .0020 .0012 .0015 .0018 .0024 1xD
and cast steel
13 Martensitic 175-440 240 .0003 .0004 .0006 .0007 .0009 .0020 .0012 .0015 .0018 .0024 1xD
Stainless steel
M 14 Austenitic 175-360 180 .0003 .0004 .0006 .0007 .0009 .0020 .0012 .0015 .0018 .0024 1xD
and cast steel
15 Grey cast iron (GG) Pearlitic/ferritic 235-740 180 .0003 .0004 .0006 .0007 .0009 .0030 .0012 .0015 .0018 .0024 1xD
16 Pearlitic/martensitic 380-700 260 .0003 .0004 .0006 .0007 .0009 .0030 .0012 .0015 .0018 .0024 1xD
17 Ferritic 440-800 160 .0003 .0004 .0006 .0007 .0009 .0010 .0012 .0015 .0018 .0024 1xD
K Nodular cast iron (GGG)
18 Pearlitic 440-800 250 .0003 .0004 .0006 .0007 .0009 .0010 .0012 .0015 .0018 .0024 1xD
19 Malleable cast iron Ferritic 440-800 130 .0003 .0004 .0006 .0007 .0009 .0010 .0012 .0015 .0018 .0024 1xD
20 Pearlitic 415-710 230 .0003 .0004 .0006 .0007 .0009 .0010 .0012 .0015 .0018 .0024 1xD
31 Fe based Annealed 60-120 200 .0003 .0004 .0006 .0007 .0009 .0010 .0012 .0015 .0018 .0024 1xD
32 High temp. Cured 60-90 280 .0003 .0004 .0006 .0007 .0009 .0010 .0012 .0015 .0018 .0024 1xD
33 alloys Ni or Co Annealed 60-90 250 .0003 .0004 .0006 .0007 .0009 .0010 .0012 .0015 .0018 .0024 1xD
S 34 based Cured 60-90 350 .0003 .0004 .0006 .0007 .0009 .0010 .0012 .0015 .0018 .0024 1xD
35 Cast 60-90 320 .0003 .0004 .0006 .0007 .0009 .0010 .0012 .0015 .0018 .0024 1xD
36 Pure 90-235 310 .0003 .0004 .0006 .0007 .0009 .0020 .0012 .0015 .0018 .0024 1xD
Titanium Ti alloys
37 Alpha+beta alloys cured 80-235 310 .0003 .0004 .0006 .0007 .0009 .0010 .0012 .0015 .0018 .0024 1xD
Roughing Cutting Diameter Feed (IPT) Profiling Radial
Material No. Cutting Speed Recommendations (Vc) SFM Hardness HB
ISO Material Condition 1/8 3/16 1/4 5/16 3/8 7/16 1/2 5/8 3/4 1 ap ae
985- .00035- .0005- .0007- .0008- .001- .0011- .0013- .0016- .0019- .0026- .75xD- .25xD-
1 <.25%C Annealed 125
1000 .0004 .0006 .0008 .001 .0012 .0014 .0016 .002 .0024 .0031 1.5xD .4xD
785- .00035- .0005- .0007- .0008- .001- .0011- .0013- .0016- .0019- .0026- .75xD- .25xD-
2 Non-alloy >=.25%C Annealed 850 190 .0004 .0006 .0008 .001 .0012 .0014 .0016 .002 .0024 .0031 1.5xD .4xD
steel Quench
and cast 630- .00035- .0005- .0007- .0008- .001- .0011- .0013- .0016- .0019- .0026- .75xD- .25xD-
3 <.55%C and 250
steel, free tempered 810 .0004 .0006 .0008 .001 .0012 .0014 .0016 .002 .0024 .0031 1.5xD .4xD
cutting
4 steel >=.55%C Annealed 630- 220 .00035- .0005- .0007- .0008- .001- .0011- .0013- .0016- .0019- .0026- .75xD- .25xD-
810 .0004 .0006 .0008 .001 .0012 .0014 .0016 .002 .0024 .0031 1.5xD .4xD
Quenched 560- .00035- .0005- .0007- .0008- .001- .0011- .0013- .0016- .0019- .0026- .75xD- .25xD-
5 >=.55%C 300
& tempered 660 .0004 .0006 .0008 .001 .0012 .0014 .0016 .002 .0024 .0031 1.5xD .4xD
630- .00035- .0005- .0007- .0008- .001- .0011- .0013- .0016- .0019- .0026- .75xD- .25xD-
6 Annealed 200
810 .0004 .0006 .0008 .001 .0012 .0014 .0016 .002 .0024 .0031 1.5xD .4xD
P Quenched 470- .00035- .0005- .0007- .0008- .001- .0011- .0013- .0016- .0019- .0026- .75xD- .25xD-
7 Low alloy & cast & tempered 660 275 .0004 .0006 .0008 .001 .0012 .0014 .0016 .002 .0024 .0031 1.5xD .4xD
steel (less than 5% Quenched 500- .00035- .0005- .0007- .0008- .001- .0011- .0013- .0016- .0019- .0026- .75xD- .25xD-
8 of alloying elements) 300
& tempered 660 .0004 .0006 .0008 .001 .0012 .0014 .0016 .002 .0024 .0031 1.5xD .4xD
Quenched 550- .00035- .0005- .0007- .0008- .001- .0011- .0013- .0016- .0019- .0026- .75xD- .25xD-
9 350
& tempered 660 .0004 .0006 .0008 .001 .0012 .0014 .0016 .002 .0024 .0031 1.5xD .4xD
500- .00035- .0005- .0007- .0008- .001- .0011- .0013- .0016- .0019- .0026- .75xD- .25xD-
10 High alloyed Annealed 660 200 .0004 .0006 .0008 .001 .0012 .0014 .0016 .002 .0024 .0031 1.5xD .4xD
steel, cast steel Quenched 270- .00035- .0005- .0007- .0008- .001- .0011- .0013- .0016- .0019- .0026- .75xD- .25xD-
11 and tool steel 325
& tempered 450 .0004 .0006 .0008 .001 .0012 .0014 .0016 .002 .0024 .0031 1.5xD .4xD
Ferritic/ 310- .00035- .0005- .0007- .0008- .001- .0011- .0013- .0016- .0019- .0026- .75xD- .25xD-
12 Stainless steel martensitic 590 200 .0004 .0006 .0008 .001 .0012 .0014 .0016 .002 .0024 .0031 1.5xD .4xD
22 ISCAR FLASHLINE High Productivity Tools Combined With a Great Economical Advantage .25xD-
235-
.00035- .0005- .0007- .0008- .001- .0011- .0013- .0016- .0019- .0026- .75xD-
and cast steel
13
Martensitic
240
550 .0004 .0006 .0008 .001 .0012 .0014 .0016 .002 .0024 .0031 1.5xD .4xD
Stainless steel 235- .00035- .0005- .0007- .0008- .001- .0011- .0013- .0016- .0019- .0026- .75xD- .25xD-
M 14 Austenitic 180
and cast steel 450 .0004 .0006 .0008 .001 .0012 .0014 .0016 .002 .0024 .0031 1.5xD .4xD
Pearlitic/ 310- .00035- .0005- .0007- .0008- .001- .0011- .0013- .0016- .0019- .0026- .75xD- .25xD-
15 ferritic 925 180 .0004 .0006 .0008 .001 .0012 .0014 .0016 .002 .0024 .0031 1.5xD .4xD
Grey cast iron (GG)
16 Pearlitic/ 500- 260 .00035- .0005- .0007- .0008- .001- .0011- .0013- .0016- .0019- .0026- .75xD- .25xD-
martensitic 875 .0004 .0006 .0008 .001 .0012 .0014 .0016 .002 .0024 .0031 1.5xD .4xD
590- .00035- .0005- .0007- .0008- .001- .0011- .0013- .0016- .0019- .0026- .75xD- .25xD-
17 Nodular cast Ferritic 160
.0016
.0004
.0014
.0006 .0008
.001
1.5xD
.002
.0012
.4xD
.0024 .0031
K iron (GGG) 1000 .00035- .0005- .0007- .0008- .001- .0011- .0013- .0016- .0019- .0026- .75xD- .25xD-
590-
18 Pearlitic 250
1000 .0004 .0006 .0008 .001 .0012 .0014 .0016 .002 .0024 .0031 1.5xD .4xD
590- .00035- .0005- .0007- .0008- .001- .0011- .0013- .0016- .0019- .0026- .75xD- .25xD-
19 Ferritic 1000 130 .0004 .0006 .0008 .001 .0012 .0014 .0016 .002 .0024 .0031 1.5xD .4xD
Malleable cast iron
20 Pearlitic 550- 230 .00035- .0005- .0007- .0008- .001- .0011- .0013- .0016- .0019- .0026- .75xD- .25xD-
890 .0004 .0006 .0008 .001 .0012 .0014 .0016 .002 .0024 .0031 1.5xD .4xD
.00035- .0005- .0007- .0008- .001- .0011- .0013- .0016- .0019- .0026- .75xD- .25xD-
31 Annealed 80-150 200 .0004 .0006 .0008 .001 .0012 .0014 .0016 .002 .0024 .0031 1.5xD .4xD
Fe based
32 Cured 80-115 280 .00035- .0005- .0007- .0008- .001- .0011- .0013- .0016- .0019- .0026- .75xD- .25xD-
.0016
.0012
1.5xD
.001
.0024 .0031
.002
.0004
.0014
.4xD
.0006 .0008
High
33 temp. Annealed 80-115 250 .00035- .0005- .0007- .0008- .001- .0011- .0013- .0016- .0019- .0026- .75xD- .25xD-
1.5xD
.0024 .0031
.0014
.0012
.002
.001
.4xD
.0006 .0008
.0004
.0016
alloys Ni or Co .00035- .0005- .0007- .0008- .001- .0011- .0013- .0016- .0019- .0026- .75xD- .25xD-
S 34 Cured 80-115 350
based .0004 .0006 .0008 .001 .0012 .0014 .0016 .002 .0024 .0031 1.5xD .4xD
.00035- .0005- .0007- .0008- .001- .0011- .0013- .0016- .0019- .0026- .75xD- .25xD-
35 Cast 80-115 320
.0004 .0006 .0008 .001 .0012 .0014 .0016 .002 .0024 .0031 1.5xD .4xD
120- .00035- .0005- .0007- .0008- .001- .0011- .0013- .0016- .0019- .0026- .75xD- .25xD-
36 Pure 295 310 .0004 .0006 .0008 .001 .0012 .0014 .0016 .002 .0024 .0031 1.5xD .4xD
Titanium Ti alloys Alpha+beta 110- .00035- .0005- .0007- .0008- .001- .0011- .0013- .0016- .0019- .0026- .75xD- .25xD-
37 310
alloys cured 220 .0004 .0006 .0008 .001 .0012 .0014 .0016 .002 .0024 .0031 1.5xD .4xD
110- 55 .00035- .0005- .0007- .0008- .001- .0011- .0013- .0016- .0019- .0026- .75xD-
38 Hardened 210 HRC .0004 .0006 .0008 .001 .0012 .0014 .0016 .002 .0024 .0031 1.5xD .02xD
Hardened Steel
39 Hardened 110- 60 .00035- .0005- .0007- .0008- .001- .0011- .0013- .0016- .0019- .0026- .75xD- .02xD
1.5xD
.001
.002
.0024 .0031
.0016
145
.0004
.0012
.0014
.0006 .0008
H 250- HRC .00035- .0005- .0007- .0008- .001- .0011- .0013- .0016- .0019- .0026- .75xD-
40 Chilled Cast Iron Cast 400 .02xD
320 .0004 .0006 .0008 .001 .0012 .0014 .0016 .002 .0024 .0031 1.5xD
110- 55 .00035- .0005- .0007- .0008- .001- .0011- .0013- .0016- .0019- .0026- .75xD-
41 Cast Iron Hardened .02xD
210 HRC .0004 .0006 .0008 .001 .0012 .0014 .0016 .002 .0024 .0031 1.5xD
Semi-Finish Cutting Diameter Feed (IPT) Profiling
Radial
Material No. Cutting Speed Recommendations (Vc) SFM Hardness HB
ISO Material Condition 1/8 3/16 1/4 5/16 3/8 7/16 1/2 5/8 3/4 1 ap ae
1 >=.25%C Annealed 1230 125 .0009 .0013 .0017 .0021 .0025 .0030 .0034 .0042 .0050 .0068 1xD .05xD
2 Annealed 1015 190 .0009 .0013 .0017 .0021 .0025 .0030 .0034 .0042 .0050 .0068 1xD .05xD
Non-alloy Quench and
3 <.55%C 900 250 .0009 .0013 .0017 .0021 .0025 .0030 .0034 .0042 .0050 .0068 1xD .05xD
steel and cast tempered
4 steel, free >=.55%C Annealed 900 220 .0009 .0013 .0017 .0021 .0025 .0030 .0034 .0042 .0050 .0068 1xD .05xD
cutting steel Quenched &
5 760 300 .0009 .0013 .0017 .0021 .0025 .0030 .0034 .0042 .0050 .0068 1xD .05xD
>=.55%C tempered
6 Annealed 900 200 .0009 .0013 .0017 .0021 .0025 .0030 .0034 .0042 .0050 .0068 1xD .05xD
Quenched &
7 710 275 .0009 .0013 .0017 .0021 .0025 .0030 .0034 .0042 .0050 .0068 1xD .05xD
P Low alloy & cast tempered
8 steel (less than 5% of Quenched & 730 300 .0009 .0013 .0017 .0021 .0025 .0030 .0034 .0042 .0050 .0068 1xD .05xD
tempered
alloying elements)
9 Quenched & 760 350 .0009 .0013 .0017 .0021 .0025 .0030 .0034 .0042 .0050 .0068 1xD .05xD
tempered
10 Annealed 730 200 .0009 .0013 .0017 .0021 .0025 .0030 .0034 .0042 .0050 .0068 1xD .05xD
High alloyed steel,
11 cast steel and tool steel Quenched & 450 325 .0009 .0013 .0017 .0021 .0025 .0030 .0034 .0042 .0050 .0068 1xD .05xD
tempered
Ferritic/
12 Stainless steel martensitic 570 200 .0009 .0013 .0017 .0021 .0025 .0030 .0034 .0042 .0050 .0068 1xD .05xD
and cast steel
13 Martensitic 490 240 .0009 .0013 .0017 .0021 .0025 .0030 .0034 .0042 .0050 .0068 1xD .05xD
Stainless steel
M 14 Austenitic 425 180 .0009 .0013 .0017 .0021 .0025 .0030 .0034 .0042 .0050 .0068 1xD .05xD
and cast steel
15 Pearlitic/ferritic 780 180 .0009 .0013 .0017 .0021 .0025 .0030 .0034 .0042 .0050 .0068 1xD .05xD
Grey cast iron (GG) Pearlitic/
16 870 260 .0009 .0013 .0017 .0021 .0025 .0030 .0034 .0042 .0050 .0068 1xD .05xD
martensitic
K 17 Nodular cast iron (GGG) Ferritic 990 160 .0009 .0013 .0017 .0021 .0025 .0030 .0034 .0042 .0050 .0068 1xD .05xD
18 Pearlitic 990 250 .0009 .0013 .0017 .0021 .0025 .0030 .0034 .0042 .0050 .0068 1xD .05xD
19 Ferritic 990 130 .0009 .0013 .0017 .0021 .0025 .0030 .0034 .0042 .0050 .0068 1xD .05xD
20 Malleable cast iron Pearlitic 900 230 .0009 .0013 .0017 .0021 .0025 .0030 .0034 .0042 .0050 .0068 1xD .05xD
31 Annealed 145 200 .0009 .0013 .0017 .0021 .0025 .0030 .0034 .0042 .0050 .0068 1xD .05xD
32 Fe based Cured 120 280 .0009 .0013 .0017 .0021 .0025 .0030 .0034 .0042 .0050 .0068 1xD .05xD
33 High temp. Ni or Co Annealed 120 250 .0009 .0013 .0017 .0021 .0025 .0030 .0034 .0042 .0050 .0068 1xD .05xD
alloys
S 34 based Cured 120 350 .0009 .0013 .0017 .0021 .0025 .0030 .0034 .0042 .0050 .0068 1xD .05xD
35 Cast 120 320 .0009 .0013 .0017 .0021 .0025 .0030 .0034 .0042 .0050 .0068 1xD .05xD
36 Pure 260 310 .0009 .0013 .0017 .0021 .0025 .0030 .0034 .0042 .0050 .0068 1xD .05xD
Titanium Ti alloys Alpha+beta
37 250 310 .0009 .0013 .0017 .0021 .0025 .0030 .0034 .0042 .0050 .0068 1xD .05xD
alloys cured
55
38 Hardened 110-210 HRC .0009 0.001 .0017 .0021 .0025 .0030 .0034 .0042 .0050 .0068 1xD .02xD
Hardened Steel 60
H 39 Hardened 110-145 HRC .0009 0.001 .0017 .0021 .0025 .0030 .0034 .0042 .0050 .0068 1xD .02xD
40 Chilled Cast Iron Cast 250-320 400 .0009 0.001 .0017 .0021 .0025 .0030 .0034 .0042 .0050 .0068 1xD .02xD
55
41 Cast Iron Hardened 110-210 .0009 0.001 .0017 .0021 .0025 .0030 .0034 .0042 .0050 .0068 1xD .02xD
HRC
