Page 26 - Solid_Brochure_2021_INCH
P. 26
EBI-4-VF continued
4 Flute Ball Nose Endmills With and Without Relieved Necks
OAL Rd°
LU
APMX
DC DCONMS
Dimensions
IC608
Designation DC APMX LU DCONMS OAL NOF (1)
EBI-4 1.0-1.5CVF4 1.000 1.5000 1.5000 1.000 4.000 4 •
EBI-4 1.0-1.5/3.0CVF5 1.000 1.5000 3.0000 1.000 5.000 4 •
EBI-4 1.0-1.5/4.0CVF6 1.000 1.5000 4.0000 1.000 6.000 4 •
EBI-4 1.0-1.5/5.0CVF7 1.000 1.5000 5.0000 1.000 7.000 4 •
EBI-4 1.0-2.0CVF45 1.000 2.0000 2.0000 1.000 4.500 4 •
EBI-4 1.0-2.25CVF5 1.000 2.2500 2.2500 1.000 5.000 4 •
EBI-4 1.0-3.0CVF6 1.000 3.0000 3.0000 1.000 6.000 4 •
EBI-4 1.0-4.0CVF7 1.000 4.0000 4.0000 1.000 7.000 4 •
(1) Number of flutes
• Weldon shank available upon request. Substitute a W in place of the C in the listed designations (example - ECI-4 375-1.0C03VF2.5 = cylindrical type; ECI-4
375-1.0W03VF2.5 = Weldon type
Slotting Feed (IPT) per Cutting Diameter (inch)
Material Group No. Cutting Speed Recommendations Hardness HB Axial
ISO Material Condition Vc (SFM) 1/8 3/16 1/4 5/16 3/8 7/16 1/2 5/8 3/4 1 Slotting
ap max
1 <0.25% C Annealed 740-800 125 .001 .001 .001 .001 .001 .001 .002 .002 .003 0.004 1xD
2 ≥0.25% C Annealed 590-680 190 .001 .001 .001 .001 .001 .001 .002 .002 .003 0.004 1xD
Non-alloy steel Quenched and
3 and cast steel, <0.55% C tempered 475-650 250 .001 .001 .001 .001 .001 .001 .002 .002 .003 0.004 1xD
4 free cutting steel Annealed 475-650 220 .001 .001 .001 .001 .001 .001 .002 .002 .003 0.004 1xD
≥0.55% C Quenched and
5 420-530 300 .001 .001 .001 .001 .001 .001 .002 .002 .003 0.004 1xD
tempered
6 Annealed 475-650 200 .001 .001 .001 .001 .001 .001 .002 .002 .003 0.004 1xD
P 7 Low alloy and cast steel 355-530 275 .001 .001 .001 .001 .001 .001 .002 .002 .003 0.004 1xD
8 (less than 5% of Quenched and 380-530 300 .001 .001 .001 .001 .001 .001 .002 .002 .003 0.004 1xD
alloying elements)
tempered
9 415-530 350 .001 .001 .001 .001 .001 .001 .002 .002 .003 0.004 1xD
10 Annealed 380-530 200 .001 .001 .001 .001 .001 .001 .001 .001 .002 0.003 1xD
High alloyed steel, cast
11 steel and tool steel Quenched and 200-360 325 .001 .001 .001 .001 .001 .001 .001 .001 .002 0.003 1xD
tempered
12 Stainless steel and cast steel Ferritic/martensitic 230-475 200 .001 .001 .001 .001 .002 .002 .002 .003 .003 0.004 1xD
13 Martensitic 175-440 240 .001 .001 .001 .001 .002 .002 .002 .003 .003 0.004 1xD
M 14 Stainless steel and cast steel Austenitic, duplex 175-360 180 .001 .001 .001 .001 .001 .002 .002 .002 .003 0.004 1xD
15 Gray cast iron (GG) Ferritic / pearlitic 235-740 180 .001 .001 .002 .002 .003 .003 .004 .005 .006 0.008 1xD
16 Pearlitic / martensitic 380-700 260 .001 .001 .002 .002 .003 .003 .004 .005 .006 0.008 1xD
17 Ferritic 440-800 160 .001 .001 .001 .001 .001 .001 .002 .002 .003 0.004 1xD
K Nodular cast iron (GGG)
18 Pearlitic 440-800 250 .001 .001 .001 .001 .001 .001 .002 .002 .003 0.004 1xD
19 Malleable cast iron Ferritic 440-800 130 .001 .001 .001 .001 .001 .001 .002 .002 .003 0.004 1xD
20 Pearlitic 415-710 230 .001 .001 .001 .001 .001 .001 .002 .002 .003 0.004 1xD
31 Fe based Annealed 60-120 200 .001 .001 .001 .001 .001 .001 .002 .002 .003 0.004 1xD
32 High temperature Hardened 60-90 280 .001 .001 .001 .001 .001 .001 .002 .002 .003 0.004 1xD
33 alloys Ni or Co Annealed 60-90 250 .001 .001 .001 .001 .001 .001 .002 .002 .003 0.004 1xD
S 34 based Hardened 60-90 350 .001 .001 .001 .001 .001 .001 .002 .002 .003 0.004 1xD
35 Cast 60-90 320 .001 .001 .001 .001 .001 .001 .002 .002 .003 0.004 1xD
36 Pure 90-235 190 .001 .001 .001 .001 .002 .002 .003 .003 .003 0.004 1xD
Titanium alloys Alpha+Beta alloys,
37 80-235 310 .001 .001 .001 .001 .001 .001 .002 .002 .003 0.004 1xD
hardened
26 ISCAR FLASHLINE High Productivity Tools Combined With a Great Economical Advantage
Roughing
Material Group No. Cutting Speed Recommendations Hardness HB
Radial Profiling
Feed (IPT) per Cutting Diameter (inch)
ISO Material Condition Vc (SFM) 1/8 3/16 1/4 5/16 3/8 7/16 1/2 5/8 3/4 1 ap ae
.75xD-
1 <0.25% C Annealed 985-1000 125 .001 .001 .001 .001 .002 .002 .003 .003 .004 .005 .25xD-.4xD
1.5xD
.75xD-
2 Non-alloy ≥0.25% C Annealed 785-850 190 .001 .001 .001 .001 .002 .002 .003 .003 .004 .005 1.5xD .25xD-.4xD
steel and Quenched .75xD-
3 cast steel, <0.55% C and tempered 630-810 250 .001 .001 .001 .001 .002 .002 .003 .003 .004 .005 1.5xD .25xD-.4xD
free cutting .75xD-
4 steel Annealed 630-810 220 .001 .001 .001 .001 .002 .002 .003 .003 .004 .005 1.5xD .25xD-.4xD
≥0.55% C Quenched .75xD-
5 560-660 300 .001 .001 .001 .001 .002 .002 .003 .003 .004 .005 .25xD-.4xD
and tempered 1.5xD
.75xD-
6 Annealed 630-810 200 .001 .001 .001 .001 .002 .002 .003 .003 .004 .005 .25xD-.4xD
1.5xD
.75xD-
P 7 Low alloy and cast steel 470-660 275 .0006 .001 .001 .001 .002 .002 .002 .003 .004 .005 .25xD-.4xD
1.5xD
(less than 5% of Quenched .75xD-
8 alloying elements) and tempered 500-660 300 .0006 .001 .001 .001 .002 .002 .002 .003 .004 .005 1.5xD .25xD-.4xD
.75xD-
9 550-660 350 .0006 .001 .001 .001 .002 .002 .002 .003 .004 .005 .25xD-.4xD
1.5xD
.75xD-
10 Annealed 500-660 200 .0004 .0007 .001 .001 .001 .001 .002 .002 .003 .003 .25xD-.4xD
High alloyed steel, cast 1.5xD
11 steel and tool steel Quenched 270-450 325 .0004 .0007 .001 .001 .001 .001 .002 .002 .003 .003 .75xD- .25xD-.4xD
and tempered 1.5xD
Ferritic/ .75xD-
12 310-590 200 .0007 .001 .001 .002 .002 .002 .003 .004 .004 .006 .25xD-.4xD
Stainless steel martensitic 1.5xD
and cast steel .75xD-
13 Martensitic 235-550 240 .0007 .001 .001 .002 .002 .002 .003 .004 .004 .006 .25xD-.4xD
1.5xD
Stainless steel Austenitic, .75xD-
M 14 235-450 180 .0005 .0007 .001 .001 .001 .002 .002 .002 .003 .004 .25xD-.4xD
and cast steel duplex 1.5xD
Ferritic / .75xD-
15 pearlitic 310-925 180 .001 .001 .001 .002 .003 .003 .004 .005 .006 .008 1.5xD .25xD-.4xD
Gray cast iron (GG)
16 Pearlitic / 500-875 260 .001 .001 .001 .002 .003 .003 .004 .003 .006 .008 .75xD- .25xD-.4xD
martensitic 1.5xD
.75xD-
17 Ferritic 590-1000 160 .0006 .001 .001 .002 .003 .002 .002 .003 .004 .005 .25xD-.4xD
K Nodular cast iron (GGG) 1.5xD
18 Pearlitic 590-1000 250 .0006 .001 .001 .001 .002 .002 .002 .003 .004 .005 .75xD- .25xD-.4xD
1.5xD
.75xD-
19 Ferritic 590-1000 130 .0006 .001 .001 .001 .002 .002 .002 .003 .004 .005 1.5xD .25xD-.4xD
Malleable cast iron .75xD-
20 Pearlitic 550-890 230 .0006 .001 .001 .001 .002 .002 .002 .003 .004 .005 1.5xD .25xD-.4xD
.75xD-
31 Annealed 80-150 200 .0007 .001 .001 .001 .002 .002 .003 .003 .004 .005 1.5xD .25xD-.4xD
Fe based .75xD-
32 Hardened 80-115 280 .0007 .001 .001 .001 .002 .002 .003 .003 .004 .005 .25xD-.4xD
High 1.5xD
33 temperature Annealed 80-115 250 .0007 .001 .001 .001 .002 .002 .003 .003 .004 .005 .75xD- .25xD-.4xD
1.5xD
alloys Ni or Co .75xD-
S 34 based Hardened 80-115 350 .0007 .001 .001 .001 .002 .002 .003 .003 .004 .005 1.5xD .25xD-.4xD
.75xD-
35 Cast 80-115 320 .0007 .001 .001 .001 .002 .002 .003 .003 .004 .005 .25xD-.4xD
1.5xD
.75xD-
36 Pure 120-295 190 .0006 .001 .001 .001 .002 .002 .002 .002 .003 .004 .25xD-.4xD
1.5xD
Titanium alloys Alpha+Beta
37 alloys, 110-220 310 .0006 .001 .001 .001 .002 .002 .002 .002 .003 .004 .75xD- .25xD-.4xD
1.5xD
hardened
55 .75xD-
38 Hardened 110-210 0.001 0.001 0.001 0.001 0.002 0.002 0.003 0.003 0.004 0.005 .02xD
Hardened steel HRC 1.5xD
39 Hardened 110-145 60 0.001 0.001 0.001 0.001 0.002 0.002 0.003 0.003 0.004 0.005 .75xD- .02xD
1.5xD
H HRC .75xD-
40 Chilled cast iron Cast 250-320 400 0.001 0.001 0.001 0.001 0.002 0.002 0.003 0.003 0.004 0.005 .02xD
1.5xD
55 .75xD-
41 Cast iron Hardened 110-210 0.001 0.001 0.001 0.001 0.002 0.002 0.003 0.003 0.004 0.005 .02xD
HRC 1.5xD
Semi-Finish and Finishing Radial
Material Group No. Cutting Speed Recommendations Hardness HB Feed (IPT) per Cutting Diameter (inch) Profiling
ISO Material Condition Vc (SFM) 1/8 3/16 1/4 5/16 3/8 7/16 1/2 5/8 3/4 1 ap ae
1 <0.25% C Annealed 1230 125 .0005 .0008 .001 .001 .001 .001 .002 .002 .002 .003 1xD .05xD
2 ≥0.25% C Annealed 1015 190 .0005 .0008 .001 .001 .001 .001 .002 .002 .002 .003 1xD .05xD
Non-alloy Quenched
3 steel and cast <0.55% C and 900 250 .0005 .0008 .001 .001 .001 .001 .002 .002 .002 .003 1xD .05xD
steel, free tempered
4 cutting steel Annealed 900 220 .0005 .0008 .001 .001 .001 .001 .002 .002 .002 .003 1xD .05xD
≥0.55% C Quenched
5 760 300 .0005 .0008 .001 .001 .001 .001 .002 .002 .002 .003 1xD .05xD
& tempered
6 Annealed 900 200 .0005 .0008 .001 .001 .001 .001 .002 .002 .002 .003 1xD .05xD
Quenched
P 7 Low alloy & cast steel & tempered 710 275 .0005 .0007 .001 .001 .001 .001 .002 .002 .003 .004 1xD .05xD
(less than 5% of Quenched
8 alloying elements) & tempered 730 300 .0005 .0007 .001 .001 .001 .001 .002 .002 .003 .004 1xD .05xD
Quenched
9 760 350 .0005 .0007 .001 .001 .001 .001 .002 .002 .003 .004 1xD .05xD
& tempered
10 Annealed 730 200 .0003 .0004 .0005 .0006 .0008 .0009 .001 .001 .001 .002 1xD .05xD
High alloyed steel,
11 cast steel and tool steel Quenched 450 325 .0003 .0004 .0005 .0006 .0008 .0009 .001 .001 .001 .002 1xD .05xD
& tempered
Ferritic/
12 570 200 .0004 .0007 .001 .001 .001 .001 .002 .002 .003 .003 1xD .05xD
Stainless steel and cast steel martensitic
13 Martensitic 490 240 .0004 .0007 .001 .001 .001 .001 .002 .002 .003 .003 1xD .05xD
Austenitic,
M 14 Stainless steel and cast steel 425 180 .0004 .0005 .0007 .001 .001 .001 .001 .001 .002 .003 1xD .05xD
duplex
Ferritic /
15 780 180 .001 .001 .002 .002 .003 .003 .003 .004 .005 .007 1xD .05xD
pearlitic
Grey cast iron (GG) Pearlitic/
16 870 260 .001 .001 .002 .002 .003 .003 .003 .004 .005 .007 1xD .05xD
K 17 martensitic 990 160 .0004 .0006 .0008 .001 .001 .001 .001 .002 .002 .003 1xD .05xD
Ferritic
18 Nodular cast iron (GGG) Pearlitic 990 250 .0004 .0006 .0008 .001 .001 .001 .001 .002 .002 .003 1xD .05xD
19 Malleable cast iron Ferritic 990 130 .0004 .0006 .0008 .001 .001 .001 .001 .002 .002 .003 1xD .05xD
20 Pearlitic 900 230 .0004 .0006 .0008 .001 .001 .001 .001 .002 .002 .003 1xD .05xD
31 Annealed 145 200 .0003 .0004 0.006 .0007 .0008 .001 .001 .001 .002 .002 1xD .05xD
32 High temp. Fe based Hardened 120 280 .0003 .0004 0.006 .0007 .0008 .001 .001 .001 .002 .002 1xD .05xD
33 alloys Annealed 120 250 .0003 .0004 0.006 .0007 .0008 .001 .001 .001 .002 .002 1xD .05xD
34 Ni or Co based Hardened 120 350 .0003 .0004 0.006 .0007 .0008 .001 .001 .001 .002 .002 1xD .05xD
S 35 Cast 120 320 .0003 .0004 0.006 .0007 .0008 .001 .001 .001 .002 .002 1xD .05xD
36 Pure 260 190 .0003 .0004 0.006 .0007 .001 .001 .001 .001 .002 .002 1xD .05xD
Titanium alloys Alpha+Beta
37 alloys, 250 310 .0003 .0004 0.006 .0007 .001 .001 .001 .001 .002 .002 1xD .05xD
hardened
38 Hardened Steel Hardened 110-210 55 HRC .0003 .0004 0.006 .0007 .0008 .001 .001 .001 .002 .002 1xD .02xD
39 Hardened 110-145 60 HRC .0003 .0004 0.006 .0007 .0008 .001 .001 .001 .002 .002 1xD .02xD
H 40 Chilled Cast Iron Cast 250-320 400 .0003 .0004 0.006 .0007 .0008 .001 .001 .001 .002 .002 1xD .02xD
41 Cast Iron Hardened 110-210 55 HRC .0003 .0004 0.006 .0007 .0008 .001 .001 .001 .002 .002 1xD .02xD
