Page 80 - Turning_catalog_INCH_2022_45_P261-508

GROOVE-TURN PENTA 34N-J Dimensions RE CW ±.0016 1.34 Machining Data

Inserts with 5 Cutting Edges
for Parting and Grooving Soft
Materials, Parting Tubes, Small
and Thin-Walled Parts
.169
Recommended

f groove
CW
RE
Designation
(IPR)
PENTA 34N150J015 .059 .0059 CWTOL (1) RETOL (2) CDX (3) • IC908 .0012-.0039
.0001
.335
.0008
PENTA 34N200J020 .079 .0079 .0008 .0001 .335 • .0016-.0047
PENTA 34N200J100 .079 .0394 .0008 .0001 .335 • .0020-.0047
PENTA 34N239J015 .094 .0059 .0008 .0001 .335 • .0016-.0063
PENTA 34N239J120 .094 .0472 .0008 .0001 .335 • .0024-.0063
PENTA 34N250J020 .098 .0079 .0008 .0001 .335 • .0016-.0063
PENTA 34N270J010 .106 .0039 .0008 .0001 .394 • .0016-.0063
PENTA 34N300J000 .118 .0000 .0008 .0000 .394 • .0016-.0039
PENTA 34N300J020 .118 .0079 .0008 .0001 .394 • .0016-.0063
PENTA 34N300J040 .118 .0157 .0008 .0001 .394 • .0016-.0063
PENTA 34N300J150 .118 .0590 .0008 .0001 .394 • .0024-.0079
PENTA 34N318J020 .125 .0079 .0008 .0001 .394 • .0079-.0063
• Recessing is possible only with 094" and wider inserts • For cutting speed recommendations and user guide, see pages 471-488
(1) Cutting width tolerance (+/-)
(2) Corner radius tolerance (+/-)
(3) For grooving and parting depths relative to part diameter, see page 339
For tools, see pages: PCADR/L (330) • PCADR/L 34N-RE (331) • PCADR/L-JHP (330) • PCHBR/L (332) • PCHPR/L (329) • PCHR/L-34 (328)
• PCHR/L-34-JHP (328)

CW CDX .137 Ref.
GTGA RE
Precision Shallow Grooving
Inserts with 3 Cutting Edges
.375
GTGA 16 ER/IL shown
Recommended
Dimensions Tough 1 Hard
Machining Data

IC528 IC508 f groove
Designation CW CDX (1) CWTOL (2) RE RETOL (3) (IPR)
GTGA 16EL/IR 100 .039 .061 .0008 .004 .0012 • • .0008-.0012
GTGA 16ER/IL 100 .039 .061 .0008 .004 .0012 • • .0008-.0012
GTGA 16EL/IR 120 .047 .063 .0008 .004 .0012 • • .0008-.0012
GTGA 16ER/IL 120 .047 .063 .0008 .004 .0012 • • .0008-.0012
GTGA 16EL/IR 140 .055 .071 .0008 .004 .0012 • • .0008-.0016
GTGA 16ER/IL 140 .055 .071 .0008 .004 .0012 • • .0008-.0016
GTGA 16EL/IR 170 .067 .079 .0008 .004 .0012 • • .0012-.0020
GTGA 16ER/IL 170 .067 .079 .0008 .004 .0012 • • .0012-.0020
GTGA 16EL/IR 195 .077 .079 .0008 .004 .0012 • • .0012-.0024
GTGA 16ER/IL 195 .077 .079 .0008 .004 .0012 • • .0012-.0024
GTGA 16EL/IR 225 .089 .083 .0008 .004 .0012 • • .0016-.0024
GTGA 16ER/IL 225 .089 .083 .0008 .004 .0012 • • .0016-.0024
• Inserts for right-hand external grooving can be used as left-hand internal grooving • Use with anvil AE 16-0 on external tools and with anvil AI 16-0 on internal tools
• For cutting speed recommendations and user guide, see pages 471-488
(1) Cutting depth maximum
(2) Cutting width tolerance (+/-)
(3) Corner radius tolerance (+/-)
For tools, see pages: AVC-D-SIR/L (773) • C#-SER/L (768) • C#-SIR/L (771) • SER/L (767) • SER/L-JHP (768) • SIR/L (769)

340 ISCAR