Page 42 - ISCAR FACE GROOVING LINES

FACE GROOVE-TURN HFHR/L-3T CDX HFHR/L --3T12 HF LH H OAH
Integral Holders for Facing DAXN-DAXX CW OAL B
WF2 WF Right-hand shown

CDX OAH
28.0 SR M6X16 DIN912 HW 5.0
METRIC 29.0 SR M6X16 DIN912 HW 5.0
30.0 SR M6X16 DIN912 HW 5.0
Designation CW CDX H HF B OAL WF WF2 DAXN(2) DAXX(3) LH 30.0 SR M6X16 DIN912 HW 5.0
33.0 SR M6X16 DIN912 HW 5.0
HFHR/L 20-25-3T12 3.00 12.00 20.0 20.0 20.0 140.00 20.50 5.3 25.0 30.0 38.0 34.0 SR M6X16 DIN912 HW 5.0
HFHR/L 20-30-3T12 3.00 12.00 20.0 20.0 35.0 SR M6X16 DIN912 HW 5.0
3.00 12.00 20.0 20.0 20.0 140.00 20.50 5.3 30.0 38.0 38.0 31.0 SR M6X16 DIN912 HW 5.0
HFHR/L 20-38-3T12 3.00 12.00 20.0 20.0 36.0 SR M6X16 DIN912 HW 5.0
3.00 12.00 25.0 25.0 20.0 140.00 20.50 5.3 38.0 48.0 38.0 36.0 SR M6X16 DIN912 HW 5.0
HFHR/L 20-48-3T12 3.00 12.00 25.0 25.0 31.0 SR M6X16 DIN912 HW 5.0
3.00 12.00 25.0 25.0 20.0 140.00 20.50 5.3 48.0 60.0 38.0 36.0 SR M6X16 DIN912 HW 5.0
HFHR/L 25-25-3T12 3.00 22.00 20.0 20.0
3.00 22.00 25.0 25.0 25.0 150.00 25.50 5.3 25.0 30.0 38.0
HFHR/L 25-30-3T12 3.00 22.00 25.0 25.0
3.00 25.00 20.0 20.0 25.0 150.00 25.50 5.3 30.0 38.0 38.0
HFHR/L 25-38-3T12 3.00 25.00 25.0 25.0
HFHR/L 20-60-3T22 (1) 25.0 150.00 25.50 5.3 38.0 48.0 38.0
HFHR/L 25-48-3T22 (1)
HFHR/L 25-60-3T22 (1) 20.0 140.00 20.50 - 60.0 75.0 40.0
HFHR/L 20-75-3T25 (1)
HFHR/L 25-75-3T25 (1) 25.0 150.00 25.50 - 48.0 60.0 40.0

25.0 150.00 25.50 - 60.0 75.0 40.0

20.0 140.00 20.50 - 75.0 100.0 43.0

25.0 150.00 25.50 - 75.0 100.0 43.0

• For user guide, see pages 161-173
(1) For deep face grooving only.
(2) Minimum penetration diameter
(3) Maximum penetration diameter
For inserts, see pages: HFPR/L (68) • HFPR/L (full radius) (69)

Groove can be widened with no limitation toward or away Limitation of widening toward d
from the center except for the following tools: center (d) depends on the major D
diameter (D) as per chart
HFHR/L-#-25-3T12
Dd
25 5
26 2

≥27 0

HFHR/L-3T CDX HFHR/L --3T12 H LH H OAH
Integral Toolholders for DAXN-DAXX CW OAL B
External Facing WF2 WF

CDX

.83 Right-hand shown

INCH

Designation CW CDX H B OAL WF F1 DAXN(2) DAXX(3) LH OAH
1.000 6.000 1.020
HFHR/L 25.4-25-3T12 .118 .470 1.000 1.000 6.000 1.020 .21 .98 1.18 1.500 1.31 SR M6X16 DIN912 HW 5.0
HFHR/L 25.4-30-3T12 .118 .470 1.000 1.000 6.000 1.020
.118 .470 1.000 1.000 6.000 1.020 .21 1.18 1.50 1.500 1.35 SR M6X16 DIN912 HW 5.0
HFHR/L 25.4-38-3T12 .118 .870 1.000 1.000 6.000 1.020
HFHR/L 25.4-48-3T22 (1) .118 .870 1.000 1.000 6.000 1.020 .21 1.50 1.89 1.500 1.39 SR M6X16 DIN912 HW 5.0
HFHR/L 25.4-60-3T22 (1) .118 .980 1.000
HFHR/L 25.4-75-3T25 (1) - 1.89 2.36 1.570 1.43 SR M6X16 DIN912 HW 5.0

- 2.36 2.96 1.570 1.43 SR M6X16 DIN912 HW 5.0

- 2.95 3.94 1.690 1.43 SR M6X16 DIN912 HW 5.0

• For user guide, see pages 161-173
(1) For deep face grooving only.
(2) Minimum penetration diameter
(3) Maximum penetration diameter
For inserts, see pages: HFPR/L (68) • HFPR/L (full radius) (69)

Groove can be widened with no limitation toward or away d
from the center except for the following tools:

HFHR/L-#-25-3T12 Limitation of widening toward D
Dd center (d) depends on the major
.98 .20 diameter (D) as per chart
1.02 .08

≥1.06 0

40 ISCAR