Page 44 - ISCAR FACE GROOVING LINES

FACE GROOVE-TURN LH

HFHR/L-4T CDX H H OAH
Integral Toolholders for DAXN-DAXX CW B
External Facing HFHR/L --4T12 HBH
WF OAL
WF2
Right-hand shown
CDX
.826

INCH

Designation CW CDX F1 H B OAL WF DAXN(1) DAXX(2) LH OAH

HFHR 25.4-25-4T12 .157 .470 .24 1.000 1.000 6.000 1.020 .98 1.14 1.540 1.35 SR M6X16 DIN912 HW 5.0
HFHR/L 25.4-29-4T12 .157 .470 1.34 1.540 1.39 SR M6X16 DIN912 HW 5.0
HFHR/L 25.4-34-4T20 .157 .790 .24 1.000 1.000 6.000 1.020 1.14 1.57 1.540 1.39 SR M6X16 DIN912 HW 5.0
HFHR/L 25.4-40-4T25 .157 .980 1.89 1.730 1.43 SR M6X16 DIN912 HW 5.0
HFHR/L 25.4-48-4T25 .157 .980 .24 1.000 1.000 6.000 1.020 1.34 2.36 1.730 1.47 SR M6X16 DIN912 HW 5.0
HFHR/L 25.4-60-4T25 .157 .980 2.95 1.730 1.47 SR M6X16 DIN912 HW 5.0
HFHR/L 25.4-75-4T25 .157 .980 .24 1.000 1.000 6.000 1.020 1.57 3.94 1.730 1.47 SR M6X16 DIN912 HW 5.0
HFHR/L 25.4-100-4T25 .157 .980 5.51 1.730 1.47 SR M6X16 DIN912 HW 5.0
HFHR/L 25.4-140-4T25 .157 .980 .24 1.000 1.000 6.000 1.020 1.89 9.45 1.730 1.47 SR M6X16 DIN912 HW 5.0
HFHR/L 25.4-240-4T25 .157 .980 31.50 1.730 1.47 SR M6X16 DIN912 HW 5.0
.24 1.000 1.000 6.000 1.020 2.36

.24 1.000 1.000 6.000 1.020 2.95

.24 1.000 1.000 6.000 1.020 3.94

.24 1.000 1.000 6.000 1.020 5.51

.24 1.000 1.000 6.000 1.020 9.45

• DGN & GRIP 4.. inserts can be used only with right-hand tools, HGPL 4.. inserts with left-hand tools • For user guide, see pages 161-173
(1) Minimum penetration diameter
(2) Maximum penetration diameter
For inserts, see pages: DGN-MF (80) • DGN/DGNC/DGNM-C (79) • DGN/DGNM-J/JS/JT (82) • GRIP (70) • GRIP (full radius) (72)
• HFPR/L (68) • HFPR/L (full radius) (69) • HGPL (75)

Groove can be widened with no limitation toward or away
from the center except for the following tools:

HFHR/L-#-25-4T12 HFHR/L-#-29-4T12 Limitation of widening toward d
Dd center (d) depends on the major D
Dd 1.14 .04 diameter (D) as per chart
≥1.8 0
.98 .04

≥1.02 0

42 ISCAR