Page 47 - ISCAR FACE GROOVING LINES
P. 47
LH FACE GROOVE-TURN
HFHR/L-6T CDX HF H OAH
Integral Toolholders for DAXN-DAXX CW B
External Facing HFHR/L --6T10 HBH
WF OAL
WF2
CDX
Right-hand shown
METRIC
Designation CW CDX H HF B OAL WF2 WF DAXN(1) DAXX(2) LH OAH HBH
HFHL 20-26-6T10 6.00 10.00 20.0 20.0 20.0 140.00 7.9 21.40 26.0 30.0 39.0 29.0 - SR M6X16 DIN912 HW 5.0
HFHR/L 20-30-6T15 6.00 17.00 20.0 20.0 20.0 140.00 - 21.40 30.0 38.0 36.0 30.0 - SR M6X16 DIN912 HW 5.0
HFHR/L 25-30-6T15 6.00 17.00 25.0 25.0 25.0 150.00 - 26.40 30.0 38.0 36.0 35.0 - SR M6X16 DIN912 HW 5.0
HFHR/L 20-38-6T20 6.00 20.00 20.0 20.0 20.0 140.00 - 21.40 38.0 50.0 39.0 31.0 - SR M6X16 DIN912 HW 5.0
HFHR/L 25-100-6T20 6.00 20.00 25.0 25.0 25.0 150.00 - 26.00 100.0 200.0 40.0 33.0 - SR M6X16 DIN912 HW 5.0
HFHR/L 25-200-6T20 6.00 20.00 25.0 25.0 25.0 150.00 - 23.00 200.0 3000.0 37.5 33.0 - SR M6X16 DIN912 HW 5.0
HFHR/L 25-38-6T20 6.00 20.00 25.0 25.0 25.0 150.00 - 26.40 38.0 50.0 39.0 36.0 - SR M6X16 DIN912 HW 5.0
HFHR/L 25-50-6T20 6.00 20.00 25.0 25.0 25.0 150.00 - 23.00 50.0 65.0 37.5 33.0 - SR M6X16 DIN912 HW 5.0
HFHR/L 25-65-6T20 6.00 20.00 25.0 25.0 25.0 150.00 - 23.00 65.0 100.0 37.5 33.0 - SR M6X16 DIN912 HW 5.0
HFHR/L 20-50-6T25 6.00 25.00 20.0 20.0 20.0 140.00 - 21.40 50.0 70.0 44.0 32.0 - SR M6X16 DIN912 HW 5.0
HFHR/L 25-50-6T25 6.00 25.00 25.0 25.0 25.0 150.00 - 26.40 50.0 70.0 44.0 37.0 - SR M6X16 DIN912 HW 5.0
HFHR/L 25-100-6T32 6.00 32.00 25.0 25.0 25.0 150.00 - 26.40 100.0 180.0 51.0 37.0 - SR M6X16 DIN912 HW 5.0
HFHR/L 25-180-6T32 6.00 32.00 25.0 25.0 25.0 150.00 - 26.40 180.0 400.0 51.0 40.0 3.0 SR M6X16 DIN912 HW 5.0
HFHR/L 25-400-6T32 6.00 32.00 25.0 25.0 25.0 150.00 - 26.40 400.0 3000.0 51.0 40.0 3.0 SR M6X16 DIN912 HW 5.0
HFHR/L 25-70-6T32 6.00 32.00 25.0 25.0 25.0 150.00 - 26.40 70.0 100.0 51.0 37.0 - SR M6X16 DIN912 HW 5.0
• DGN & GRIP 6.. inserts can be used only with right-hand tools, HGPL 6.. inserts with left-hand tools • For user guide, see pages 161-173
(1) Minimum penetration diameter
(2) Maximum penetration diameter
For inserts, see pages: HFPR/L (68) • HFPR/L (full radius) (69) • GRIP (70) • GRIP (full radius) (72) • DGN/DGNC/DGNM-C (79) • DGN/DGNM-J/JS/JT (82) • HGPL (75)
Groove can be widened with no limitation toward or away Limitation of widening toward d
from the center except for the following tools: center (d) depends on the major D
diameter (D) as per chart
HFHR/L-#-30-6T10
Dd
30 7
31 4
32 1
≥33 0
45
