Page 77 - HOLE MAKING CATALOG p383-544

IC830 60° 91º 91º 95º
IC8350 91º
TCMT-SM IC8250 L
Triangular Inserts with a 7° IC908 Recommended
Positive Flank for Semi-Finishing IC8150 D1 Machining Data
and Finish Turning on Soft IC5010
Materials and Exotic Alloys IC428RE7°
IC5005ICS
IC807
Dimensions IC907Tough 1 Hard

ITS BORE
ap f

Designation L IC S RE D1 ••••• (mm) (mm/rev)
• • • 0.20-3.00 0.05-0.25
TCMT 110204-SM 11.00 6.35 2.38 0.40 2.80 • • • 0.50-2.50 0.07-0.25

TCMT 110208-SM 11.00 6.35 2.38 0.80 2.80 •
16.50 9.52 3.97 0.40 4.40 • • • • • • 0.50-3.00 0.06-0.25
TCMT 16T304-SM 16.50 9.52 3.97 0.80 4.40 • • • • • • 0.50-3.00 0.08-0.28

TCMT 16T308-SM •

TCMT 16T308-SM* 16.50 9.52 3.97 0.80 4.40 0.50-3.00 0.08-0.28

For tools, see page: IHBR (409)

WCGT 80° 93º
Trigon Inserts with a 7° L
Positive Flank and Chipformer
for Finish Turning RE 7°
IC S

Dimensions Tough 1 Hard Recommended Machining Data

IC908 ap f
IC30N
Designation L IC S RE (mm) (mm/rev)
••
WCGT 020102L 2.18 3.97 1.59 0.20 •• 0.40-2.00 0.05-0.10

WCGT 020104L 2.18 3.97 1.59 0.40 0.40-2.00 0.10-0.15

For tools, see pages: IHAXF (432) • IHAXF-AVI (434) • IHAXF-E (434) • IHWF (436)

60° 91º

TPGX L Recommended
Triangular Inserts with an 11° D1 Machining Data
Positive Flank and Ground
Chipformer for Finish Turning

RE IC 11°
S

Dimensions Tough 1 Hard

Designation L IC S RE D1 IC908 ap f
3.00 IC20
3.00 IC20N (mm) (mm/rev)
3.50 IC520N 1.00-2.00 0.10-0.20
3.50 1.00-2.50 0.15-0.20
TPGX 090202-L 9.52 5.56 2.38 0.20 3.50 •••• 1.00-2.50 0.10-0.20
•••• 1.00-3.00 0.15-0.20
TPGX 090204-L 9.52 5.56 2.38 0.40 •••• 1.00-3.50 0.15-0.25
••••
TPGX 110302-L 11.00 6.35 3.18 0.20
•
TPGX 110304-L 11.00 6.35 3.18 0.40

TPGX 110308-L 11.00 6.35 3.18 0.80

For tools, see pages: IHAXF (432) • IHAXF-AVI (434) • IHAXF-E (434) • IHFF (436) • IHFF-C (413)

459