Page 80 - HOLE MAKING CATALOG p383-544

ITS BORE LF

PICCO R/L 050, 053, 055 DCONMS
(Continue)
Inserts for Internal Turning 8° OHN DMIN
and Chamfering
a
WF 20° RE CDX

Dimensions Right-hand shown

Designation DCONMS WF a LF OHN(2) RE CDX(3) Tough 1 HardIC228
IC908
5.30 45.00 29.0 0.15 0.50 DMIN
PICCO R/L 050.6-30 6.00 2.30 5.30 50.00 34.0 0.15 0.50
PICCO R/L 050.6-35 6.00 2.30 5.30 57.00 41.0 0.15 0.50 6.00 • •
PICCO R/L 050.6-42 6.00 2.30 6.30 35.00 19.0 0.15 0.60 6.00 • •
PICCO R/L 050.7-20 7.00 2.80 6.30 40.00 24.0 0.15 0.60 6.00 • •
6.30 45.00 29.0 0.15 0.60 6.80 • •
PICCO R/L 050.7-25 7.00 2.80 6.30 50.00 34.0 0.15 0.60 6.80 • •
6.30 55.00 39.0 0.15 0.60 6.80 • •
PICCO R/L 050.7-30 7.00 2.80 6.30 60.00 44.0 0.15 0.60 6.80 • •
6.30 65.00 49.0 0.15 0.60 6.80 • •
PICCO R/L 050.7-35 7.00 2.80 6.80 • •
PICCO R/L 050.7-40 7.00 2.80 6.80 • •
PICCO R/L 050.7-45 7.00 2.80
PICCO R/L 050.7-50 7.00 2.80

• Specify right- or left-hand bars

(1) Maximum D.O.C.=0.01-0.03 mm, maximum feed=0.01 mm/rev.

(2) Minimum overhang

(3) Cutting depth maximum

LF

PICCO R 050.20 DCONMS
Inserts for Internal Turning
and Chamfering Next to the 20° OHN DMIN
Bottom of Blind Holes Right-hand shown
a

WF 20° RE CDX

Dimensions

Designation DCONMS WF a LF OHN(1) RE CDX(2) DMIN IC908

PICCO R 050.20.2-10 4.00 - 1.70 24.00 10.0 0.05 0.10 2.00 •
PICCO R 050.20.3-10 4.00 0.60 0.20 2.80 •
PICCO R 050.20.4-16 4.00 1.50 2.60 24.00 10.0 0.10 0.30 4.00 •
PICCO R 050.20.5-20 5.00 1.90 0.50 5.00 •
3.50 30.00 16.0 0.10
• Specify right- or left-hand bars
4.40 35.00 19.0 0.15
(1) Minimum overhang

(2) Cutting depth maximum

PICCO 050... PICCO 050.20...
20°
8°

462 ISCAR