Page 73 - ISCAR FACE GROOVING LINES

GRIP ±.004IC830INSL (Ref.)
Utility Double-Ended IC8250
Inserts for External, Internal IC08RE BW
and Face Machining IC808CW
IC908
IC418
IC5010
IC806
IC807
IC804

FACE GROOVE-TURN
Dimensions INCH No depth penetration limit
Tough 1 Hard
Recommended Machining Data

f face-
ap f turn f groove groove f face-turn

Designation CW CWTOL(1) RE RETOL(2) INSL BW ••• (inch) (IPR) (IPR) (IPR) (IPR)
.118 .00196 .0079 .0020 .622 .091 • • • • • .010-.071 .0055-.0071 .0027-.0043 .0031-.0079 .0039-.0079
GRIP 3002Y .118 .00196 .0118 .0020 .622 .091 • • • • • • • • .016-.071 .0059-.0075 .0027-.0043 .0031-.0079 .0039-.0079
GRIP 3003Y .125 .00196 .0157 .0020 .622 .091 • ••• • .020-.075 .0067-.0087 .0027-.0047 .0031-.0079 .0039-.0079
GRIP 318-040Y .157 .00196 .0079 .0020 .748 .110 • • • • • •• .010-.094 .0063-.0083 .0035-.0055 .0039-.0094 .0059-.0118
GRIP 4002Y .157 .00196 .0157 .0020 .748 .110 • • • • • • • • • • .020-.094 .0071-.0094 .0035-.0059 .0039-.0094 .0059-.0118
GRIP 4004Y .187 .00196 .0315 .0020 .748 .122 • • ••• • .039-.110 .0083-.0130 .0039-.0079 .0039-.0094 .0059-.0118
GRIP 476-080Y .197 .00196 .0197 .0020 .748 .130 • • • • • • • • • • .024-.118 .0079-.0118 .0043-.0079 .0047-.0094 .0059-.0138
GRIP 5005Y .197 .00196 .0315 .0020 .748 .134 • • • • • • • • .039-.118 .0091-.0138 .0043-.0083 .0047-.0094 .0059-.0138
GRIP 5008Y .236 .00196 .0197 .0020 .748 .165 • • • • • • • • .024-.142 .0087-.0142 .0051-.0091 .0047-.0110 .0059-.0157
GRIP 6005Y .236 .00196 .0315 .0020 .748 .165 • • • • • • • • .039-.142 .0094-.0165 .0051-.0098 .0047-.0110 .0059-.0157
GRIP 6008Y .250 .00196 .0315 .0020 .748 .165 • • • • • .039-.150 .0098-.0173 .0055-.0106 .0047-.0110 .0059-.0157
GRIP 635-080Y

• For cutting speed recommendations and user guide, see pages 161-173

(1) Cutting width tolerance (+/-)

(2) Corner radius tolerance (+/-)

For tools, see pages: • C#-HFIR/L-MC (145) • CR HFIR-M (65) • HFAER/L-4 (53) • HFAER/L-5T, 6T (53) • HFAIR/L-4 (60) • HFAIR/L-DG (61) • HFFR/L-T (51)

• HFHR/L-4T (41) • HFHR/L-5T (43) • HFIR/L-MC (63) • HFPAD-3 (49) • HFPAD-4 (49) • HFPAD-5 (50) • HFPAD-6 (50) • HFPAD-JHP (48) • HGAER/L-3 (52)

• HGAIR/L-3 (57) • HGHR/L-3 (39) • IM-HFIR-MC (62)

The Twisted Insert
for Face Machining

The double-ended, twisted insert body
makes it possible to machine deeper
than the inserts’ length. A unique
chipformer for controlled chip flow in
axial and radial directions.
The rear angle is slanted in relation
to the frontal edge so it does not
come into contact with the machined
groove surface as the tool penetrates
deeply into the workpiece.

71