Page 70 - ISCAR FACE GROOVING LINES

FACE GROOVE-TURN HFPR/L ±0.1 19 Ref. CW
Utility Double-Ended Face
Machining Inserts DAXN-DAXX 7°

RE BW No depth penetration limit

M ETRIC Recommended Machining Data
Dimensions Tough 1 Hard

IC830 ap f face-groove f face-turn
IC354
Designation CW RE CWTOL(1) RETOL(2) BW DAXN(3) DAXX(4) IC8250 (mm) (mm/rev) (mm/rev)
IC808 0.10-0.20
HFPR/L 3003 IC9015 0.15-0.25
HFPR/L 4004 IC20 0.15-0.35
HFPR/L 5004 IC5010 0.15-0.40
HFPR/L 6004 IC806

3.00 0.30 0.05 0.050 2.10 25.6 51.5 • • • • • • • 0.30-1.50 0.08-0.20
4.00 0.40 0.05 0.050 2.80 24.1 73.7 • • • • • • • 0.40-2.00
0.10-0.24
5.00 0.40 0.05 0.050 3.40 22.1 170.0 • • • • • • • • 0.50-2.50 0.12-0.24
6.00 0.40 0.05 0.050 4.00 20.8 - •••• • • • 0.40-3.00 0.12-0.28

• For cutting speed recommendations and user guide, see pages 161-173

(1) Cutting width tolerance (+/-)

(2) Corner radius tolerance (+/-)

(3) Minimum axial grooving diameter-applies to type M tools only. For other tools, apply the diameter limitations that are recorded on each tool.

(4) Maximum axial grooving diameter-applies to type M tools only. For other tools, apply the diameter limitations that are recorded on each tool.

For tools, see pages: C#-HFIR/L-MC (145) • CR HFIR-M (65) • HFAER/L-4 (53) • HFAER/L-5T, 6T (53) • HFAIR/L-4 (60) • HFAIR/L-DG (61)

• HFFR/L-T (51) • HFHPR/L-M (55) • HFHR/L-3T (40) • HFHR/L-4T (41) • HFHR/L-5T (43) • HFHR/L-6T (45) • HFHR/L-M (54) • HFIR/L-MC (63)

• HFPAD-4 (49) • HFPAD-5 (50) • HFPAD-6 (50) • HFPAD-JHP (48) • IM-HFIR-MC (62)

HFPR/L ±.004 .748 Ref. CW
Utility Double-Ended Face
Machining Inserts DAXN-DAXX 7°

RE BW No depth penetration limit

Dimensions INCH Recommended Machining Data
Tough 1 Hard

IC830 ap f face-groove f face-turn
IC354
Designation CW RE CWTOL(1) RETOL(2) BW DAXN(3) DAXX(4) IC8250 (inch) (IPR) (IPR)
IC808 .0039-.0079
HFPR/L 3003 IC9015 .0059-.0098
HFPR/L 4004 IC20 .0059-.0138
HFPR/L 5004 IC5010 .0059-.0157
HFPR/L 6004 IC806

.118 .012 .0020 .0020 .083 1.01 2.03 • • • • • • • .012-.059 .0031-.0079
.157 .016 .0020 .0020 .110 .95 2.90 • • • • • • • .016-.079 .0039-.0094
6.69 • • • • • • • • .020-.098 .0047-.0094
.197 .016 .0020 .0020 .134 .87 - •••• • • • .016-.118 .0047-.0110

.236 .016 .0020 .0020 .157 .82

• For cutting speed recommendations and user guide, see pages 161-173

(1) Cutting width tolerance (+/-)

(2) Corner radius tolerance (+/-)

(3) Minimum axial grooving diameter-applies to type M tools only. For other tools, apply the diameter limitations that are recorded on each tool.

(4) Maximum axial grooving diameter-applies to type M tools only. For other tools, apply the diameter limitations that are recorded on each tool.

For tools, see pages: C#-HFIR/L-MC (145) • CR HFIR-M (65) • HFAER/L-4 (53) • HFAER/L-5T, 6T (53) • HFAIR/L-4 (60) • HFAIR/L-DG (61)

• HFFR/L-T (51) • HFHPR/L-M (55) • HFHR/L-3T (40) • HFHR/L-4T (41) • HFHR/L-5T (43) • HFHR/L-6T (45) • HFHR/L-M (54) • HFIR/L-MC (63)

• HFPAD-4 (49) • HFPAD-5 (50) • HFPAD-6 (50) • HFPAD-JHP (48) • IM-HFIR-MC (62)

68 ISCAR