Page 71 - ISCAR FACE GROOVING LINES
P. 71
HFPR/L (full radius) ±0.1 IC83019 Ref. CW
Utility Double-Ended Full Radius IC354
Face Machining Inserts DAXN-DAXX IC82507°
IC808
IC9015RE BW
IC20
METRIC IC5010 No depth penetration limit.
IC806
Dimensions Tough 1 Hard Recommended Machining Data
FACE GROOVE-TURN
ap f face- f face-turn
groove
Designation CW RE CWTOL(1) RETOL(2) BW DAXN(3) DAXX(4) (mm) (mm/rev)
3.00 1.50 0.05 0.050 2.10 25.6 51.5 • • • • • • • 0.00-1.50 (mm/rev) 0.12-0.20
HFPR/L 3015 4.00 2.00 0.05 0.050 2.80 24.1 73.7 • • • • • • • 0.00-2.00 0.08-0.20 0.15-0.25
HFPR/L 4020 5.00 2.50 0.05 0.050 3.40 22.1 170.0 • • • • • • • 0.00-2.50 0.10-0.24 0.15-0.35
HFPL 5025 5.00 2.50 0.05 0.050 3.40 22.1 170.0 • • • • • • • 0.00-2.50 0.12-0.24 0.15-0.35
HFPR 5025 6.00 3.00 0.05 0.050 4.00 20.8 - •••• • • • 0.00-3.00 0.12-0.24 0.20-0.40
HFPR/L 6030 0.12-0.28
• For cutting speed recommendations and user guide, see pages 161-173
(1) Cutting width tolerance (+/-)
(2) Corner radius tolerance (+/-)
(3) Minimum axial grooving diameter-applies to type M tools only. For other tools, apply the diameter limitations that are recorded on each tool.
(4) Maximum axial grooving diameter-applies to type M tools only. For other tools, apply the diameter limitations that are recorded on each tool.
For tools, see pages: C#-HFIR/L-MC (145) • CR HFIR-M (65) • HFAER/L-4 (53) • HFAER/L-5T, 6T (53) • HFAIR/L-4 (60) • HFAIR/L-DG (61)
• HFFR/L-T (51) • HFHPR/L-M (55) • HFHR/L-3T (40) • HFHR/L-4T (41) • HFHR/L-5T (43) • HFHR/L-6T (45) • HFHR/L-M (54) • HFIR/L-MC (63)
• HFPAD-4 (49) • HFPAD-5 (50) • HFPAD-6 (50) • HFPAD-JHP (48) • IM-HFIR-MC (62)
HFPR/L (full radius) ±.004 .748 Ref. CW
Utility Double-Ended Full Radius
Face Machining Inserts DAXN-DAXX 7°
RE BW
Dimensions INCH No depth penetration limit.
Tough 1 Hard
Recommended Machining Data
IC830 ap f face- f face-turn
IC354 groove
Designation CW RE CWTOL(1) RETOL(2) BW DAXN(3) DAXX(4) IC8250 (inch) (IPR)
IC808 (IPR) .0047-.0079
HFPR/L 3015 IC9015 .0031-.0079 .0059-.0098
HFPR/L 4020 IC20 .0039-.0094 .0059-.0138
HFPL 5025 IC5010 .0047-.0094 .0059-.0138
HFPR 5025 IC806 .0047-.0094 .0079-.0157
HFPR/L 6030 .0047-.0110
.118 .059 .0020 .0020 .083 1.01 2.03 • • • • • • • .000-.059
.157 .079 .0020 .0020 .110 .95 2.90 • • • • • • • .000-.079
.197 .098 .0020 .0020 .134 .87 6.69 • • • • • • • .000-.098
.197 .098 .0020 .0020 .134 .87 6.69 • • • • • • • .000-.098
.236 .118 .0020 .0020 .157 .82 - •••• • • • .000-.118
• For cutting speed recommendations and user guide, see pages 161-173
(1) Cutting width tolerance (+/-)
(2) Corner radius tolerance (+/-)
(3) Minimum axial grooving diameter-applies to type M tools only. For other tools, apply the diameter limitations that are recorded on each tool.
(4) Maximum axial grooving diameter-applies to type M tools only. For other tools, apply the diameter limitations that are recorded on each tool.
For tools, see pages: C#-HFIR/L-MC (145) • CR HFIR-M (65) • HFAER/L-4 (53) • HFAER/L-5T, 6T (53) • HFAIR/L-4 (60) • HFAIR/L-DG (61)
• HFFR/L-T (51) • HFHPR/L-M (55) • HFHR/L-3T (40) • HFHR/L-4T (41) • HFHR/L-5T (43) • HFHR/L-6T (45) • HFHR/L-M (54) • HFIR/L-MC (63)
• HFPAD-4 (49) • HFPAD-5 (50) • HFPAD-6 (50) • HFPAD-JHP (48) • IM-HFIR-MC (62)
69
