Page 152 - MILLING CATALOG p319-550

MILLING INSERTS 60°

TPMT L
Triangular 11° Positive Inserts
with a Positive Chipformer D1
Exerting Low Cutting Forces
for Internal Finish Turning RE IC 11°
S

Dimensions Tough 1 Hard Recommended
Machining Data

IC830 f
IC635 ap (mm/
Designation L IC S RE D1 IC50M (mm)(1) rev)(2)
IC8350
TPMT 110202 IC8250
TPMT 110204 IC8150
TPMT 110208 IC520M
TPMT 160304 IC20
TPMT 160308 IC806
IC807
IC907

11.00 6.35 2.38 0.20 3.00 • • • 0.20-2.00 0.05-0.25
11.00 6.35 2.38 0.40 3.00 • • • • • • 1.00-3.00 0.12-0.30
11.00 6.35 2.38 0.80 3.00 • •• • 1.00-4.00 0.15-0.30
16.50 9.52 3.18 0.40 4.30 • •• • • • 1.00-4.00 0.12-0.30
16.50 9.52 3.18 0.80 4.30 • • • • • • • • • 5.00-12.00 0.15-0.35

• For cutting speed recommendations, see pages 542-547

(1) For turning

(2) For turning

For tools, see pages: E30 / T230 (36) • E45 / T245 (38) • E60 / T260 (39)

TPKN/TPKR PP-R PP-N
11° Positive Triangular Milling L
Inserts for General Use BS
IC BS
S BS

Dimensions Tough 1 Hard Recommended
Machining Data

IC328 ap fz
IC928
IC L S IC50M
3.18 IC250
3.18 IC950
3.18 IC910
3.18 IC520M
3.50 IC20
Designation 4.76 BS (mm) (mm/t)
4.76 • 3.00-10.00
TPKN 1603PP-R-42 9.52 16.50 4.76 1.40 • 3.00-10.00 0.10-0.15
TPKN 1603PPFR 9.52 16.50 4.76
TPKN 1603PPTR 9.52 16.50 4.76 1.40 0.10-0.15
TPKN 1603PPTR-42 9.52 16.50 1.40 • •
TPKR 1603PPTR-HS 9.52 16.50 1.47 • •• 3.00-10.00 0.10-0.15
TPKN 2204PDFR 12.70 22.00
1.45 • • 3.00-10.00 0.10-0.15

3.00-10.00 0.12-0.20
• 3.00-15.00
1.40 0.10-0.15
1.45 • •
TPKN 2204PDTR 12.70 22.00 1.80 • ••••• 3.00-15.00 0.10-0.15

TPKN 2204PDTR-42 12.70 22.00 1.80 • • 3.00-15.00 0.10-0.15
12.70 22.00
TPKR 2204PD-R-76 12.70 22.00 1.88 • • • • 3.00-15.00 0.10-0.15
TPKR 2204PDTR-HS
3.00-15.00 0.12-0.20

• For cutting speed recommendations, see pages 542-547
For tools, see pages: F90 (214)

H690 WNMU 0403 IC Rd°
Trigonal Inserts with 6
Helical Cutting Edges for APMX L
90° Shoulder Milling S BS RE

Dimensions Tough 1 Hard Recommended Machining Data

Designation L APMX IC S RE BS IC830 ap fz
IC5400
IC808 (mm) (mm/t)
IC810 0.80-4.00 0.08-0.18
IC5100 0.80-4.00 0.08-0.15
1.20-4.00 0.08-0.15
H690 WNMU 0403-PNTR 4.20 4.00 6.70 3.50 0.40 0.80 ••
H690 WNMU 0403PNR-MM 4.20 4.00 6.70 3.50 0.40 0.80 • •
H690 WNMU040308PNR-MM 4.20 4.00 6.70 3.50 0.80 0.40 • • •

• For cutting speed recommendations, see pages 542-547

For tools, see pages: H690 EWN-04 (12) • H690 EWN-MM-04 (12) • H690 FWN-04 (193)

PNTR PNR-MM

468 ISCAR