Page 154 - MILLING CATALOG p319-550
P. 154
MILLING INSERTS REN 3°30’
RE
H490 ANKX 0904-FF INSL Rd°
Double-Sided Rectangular
Inserts with 4 Helical Cutting BS APMX
Edges for Fast Feed Milling W1
at Small Depths of Cut
S
Dimensions Tough 1 Hard Recommended
Machining Data
IC830 ap fz
IC808
Designation W1 BS APMX(1) INSL S RE Rg(2) REN (mm) (mm/t)
H490 ANKX 0904R12T-FF 6.20 2.30 1.00 8.50 4.30 1.00 1.20 5.00 •
• 0.50-1.00 0.50-1.50
• The cutting diameter of the tool is 0.12 mm larger than the nominal diameter when using this insert • At D.O.C. larger than APMX, regular insert feed should be applied
• Enables ramping down at 1° maximum on 16 to 40 tool diameters
(1) For fast feed
(2) Radius for programming
For tools, see pages: H490 E90AX-09 (20) • H490 E90AX-M (20) • H490 E90AX-MM (21) • H490 F90AX-09 (197)
H490 ANKX/ANCX-12 W13
Double-Sided Rectangular Inserts L1
with 4 Helical Cutting Edges
BS RE
S
Dimensions Tough 1 Hard Recommended
Machining Data
IC330 ap fz
IC830
Designation W1 RE S L BS IC380 (mm) (mm/t)
10.00 0.80 IC808
H490 ANCX 120508PDR 10.00 0.40 IC810
H490 ANKX 120504PNTR 10.00 0.80 IC5100
H490 ANKX 120508PNTR 10.00 1.00
H490 ANKX 120510PNTR 10.00 1.20 9.45 13.67 3.50 •• 1.20-11.00 0.08-0.15
H490 ANKX 120512PNTR 10.00 1.60 9.15 13.70 3.80 • 0.80-11.00 0.10-0.30
H490 ANKX 120516PNTR 10.00 2.00 9.15 13.67 3.50 • • • • • • 1.20-11.00 0.10-0.30
H490 ANKX 120520PNTR 10.00 2.40 8.90 13.70 3.40 • 1.40-11.00 0.10-0.30
H490 ANKX 120524PNTR 10.00 0.80 •
H490 ANKX 1205PNTR-CS (1) 10.00 0.80 8.90 13.70 3.20 • 1.60-11.00 0.10-0.30
H490 ANKX 1205PNTR-RM
8.60 13.70 2.80 • 2.00-11.00 0.10-0.30
8.70 13.60 2.80 • 2.40-11.00 0.10-0.30
8.60 13.70 2.80 • 2.80-11.00 0.10-0.30
9.15 13.70 3.50 •• 1.20-11.00 0.15-0.20
9.15 13.70 3.50 1.20-11.00 0.20-0.30
• ANKX-utility inserts, ANCX-precision inserts • For cutting speed recommendations, see pages 542-547
(1) The maximum feed per tooth for chip splitting effect is up to 0.20 mm/t.
For tools, see pages: H490 E90AX-12 (30) • H490 F90AX-12 (206) • H490 SM-12 (243)
470 ISCAR
