Page 100 - TURNING CATALOG p121-254

ISOTURN INSERTS 60° 22°MAX
L
TPGN-Ceramic 91º 93º 91º
Triangular Ceramic Inserts IC 11° S
with an 11° Positive Flank for 95º 91º 55°
Machining Hardened Steel Tough 1 Hard MAX
RE
60º
0.40 •
RE 0.40 • • •
0.80 • • •
Dimensions 0.40 • • • Recommended Machining Data
0.80 • • •
Designation L IC S IN23 ap f
IN22
IN420 (mm) (mm/rev)
0.10-1.50 0.07-0.30
TPGN 090204T 9.60 5.56 2.38 0.10-1.50 0.07-0.30
TPGN 110304T 11.00 6.35 3.18 0.10-3.00 0.07-0.40
11.00 6.35 3.18 0.10-4.00 0.07-0.50
TPGN 110308T 0.10-4.00 0.07-0.50

TPGN 160304T 16.50 9.52 3.18
TPGN 160308T 16.50 9.52 3.18

• For user guide and cutting speed recommendations, see pages 122-134, 236-248

For tools, see pages: CTFPR/L (75) • CTGPR/L (74) • S-CTFPR/L (116)

CH

RPGN-Ceramic 11°
Round Ceramic Inserts for IC
Machining Nickel Based
Alloys and Hardened Steel S

Dimensions Tough 1 Hard Recommended Machining Data

Designation IC S IW7 • ap f
IS35••
RPGN 090300E 9.52 3.17 IS25 IW7•• (mm) (mm/rev)
RPGN 120400E 12.70 4.76 IN23 IS35 0.10-2.00 0.07-0.20
12.70 4.76 ••• 0.10-3.00 0.07-0.20
RPGN 120400E-CH (1) IS25•• 0.10-3.00 0.07-0.20
IN22 0.10-3.00 0.07-0.20
RPGN 120400T 12.70 4.76 IN420 0.10-3.00 0.07-0.20
RPGN 120400T-CH (1) 12.70 4.76

• For user guide and cutting speed recommendations, see pages 122-134, 236-248

(1) Insert with a dimple

RNGN-Ceramic CH
Round Double-Sided Ceramic IC
Inserts for Machining Cast
Iron, Nickel Based Alloys S
and Hardened Steel

Dimensions Tough 1 Hard Recommended Machining Data

Designation IC S • ap f
3.18 •
RNGN 090300T 9.52 4.76 • (mm) (mm/rev)
RNGN 090400T 9.52 4.76 • • •
RNGN 120400T 12.70 7.94 • • 0.10-2.00 0.07-0.20
RNGN 120700 S6 (1) 12.70 7.94 • • • 0.10-2.00 0.07-0.20
RNGN 120700E 12.70 7.94 • • 0.10-3.50 0.07-0.50
RNGN 120700E-CH (2) 12.70 7.94 • • • • • 0.10-2.00
RNGN 120700T 12.70 7.94 • • 0.10-2.00 -
RNGN 120700T-CH (2) 12.70 7.94 • • 0.10-2.00 0.07-0.20
RNGN 120700TE 12.70 7.94 • 0.10-4.50 0.07-0.20
RNGN 120700T02020 12.70 7.94 • 0.10-4.50 0.07-0.50
RNGN 150700T 15.88 7.94 • 0.10-4.50 0.07-0.50
RNGN 190700T 19.05 7.94 • • 0.10-2.00 0.07-0.50
RNGN 190700TE 19.05 0.10-3.00 0.07-0.20
0.10-3.00 0.07-0.20
0.10-3.00 0.07-0.20
0.07-0.20

• For user guide and cutting speed recommendations, see pages 122-134, 236-248

(1) For milling nickel based superalloys; reference recommendations for milling Inconel 718: 0.12 mm/t 900-1000 m/min

(2) Insert with a dimple

For tools, see pages: CRDNN (90) • CRGNR/L (90)

220 ISCAR