Page 124 - Turning_catalog_INCH_2022_45_P509-690

FACE GROOVING GHFG-R/L-8 .315 CDX DAXN CDX DAXX (2) DAXN-DAXX HF 1.000 OAL 6.000 H B GHFG-25-50R-8 .870 SR M6X20 DIN912 HW 5.0
LH
Holders for Face Grooving
and Turning Along Shafts
CW
WF

Right-hand shown

(1)
Designation
CW
H
LH
WF
OAL
HF
B
GHFG 25.4-50R/L-8
1.000
1.000
1.600
1.000
1.97
2.52
GHFG 25.4-63R/L-8
.870
1.000
.315
3.23
1.000
HW 5.0
2.48
SR M6X20 DIN912
6.000
1.000
1.000
1.600
• For user guide, see pages 607-612, 663-669
(1) Minimum penetration diameter
(2) Maximum penetration diameter
For inserts, see pages: GDMF (298) • GDMM-CC (637) • GDMN (299) • GDMU (299) • GDMY (298) • GDMY (full radius) (300) • GDMY-F (301)
• GIA-K (long pocket) (310) • GIF (long pocket) (308) • GIF-E (W=315,394 full radius) (304) • GIF-E (W=315,394) (302)
• GIFG-E (W=315) (634) • GIPA/GIDA 8 (full radius) (499)

LH
GHFGR/L-8 CDX H H
Holders for Face Turning HBH
and Grooving DAXN-DAXX OAL
WF B
CW Right-hand shown
Designation CDX DAXN (1) DAXX (2) H B CW OAL LH WF HBH
GHFGR/L 25.4-80-8 .905 3.15 4.53 1.000 1.000 .315 6.000 1.710 .840 .30 SR M6X20 DIN912 HW 5.0
GHFGR 31.7-80-8 .905 3.15 4.53 1.250 1.250 .315 7.000 1.710 1.110 - SR M6X25 DIN912 HW 5.0
GHFGR 25.4-105-8 .984 4.13 6.30 1.000 1.000 .315 6.000 1.710 .840 .24 SR M6X20 DIN912 HW 5.0
GHFGR 31.7-105-8 .984 4.13 6.30 1.250 1.250 .315 6.700 1.710 1.110 - SR M6X20 DIN912 HW 5.0
GHFGR/L 25.4-155-8 .984 6.10 20.10 1.000 1.000 .315 6.000 1.710 .840 .24 SR M6X20 DIN912 HW 5.0
GHFGR/L 31.7-155-8 .984 6.10 20.10 1.250 1.250 .315 6.700 1.710 1.110 - SR M6X20 DIN912 HW 5.0
• No limitation to widening the groove either way after initial grooving • CDX depends on the penetration diameter and the insert
• For user guide, see pages 607-612, 663-669
(1) Minimum penetration diameter
(2) Maximum penetration diameter
For inserts, see pages: GDMF (298) • GDMM-CC (637) • GDMN (299) • GDMU (299) • GDMY (298) • GDMY (full radius) (300) • GDMY-F (301)
• GIA-K (long pocket) (310) • GIF (long pocket) (308) • GIF-E (W=315,394 full radius) (304) • GIF-E (W=315,394) (302)
• GIFG-E (W=315) (634) • GIPA/GIDA 8 (full radius) (499)
CDX for GHFGR/L (25.4/31.7)-80-8
D GIF 8… GIFG 8… GDMY 8… GIPA 8… GIDA 8… GIA 8… GDMM 8CC…
3.150 .630 .906 .906 .787 .945 .630 .945
3.228 .669 .906 .906 .787 .945 .669 .945
3.307 .709 .906 .906 .827 .945 .709 .945
3.386 .748 .906 .906 .827 .945 .748 .945
3.465 .787 .906 .906 .866 .945 .787 .945
3.543 .787 .906 .906 .866 .945 .787 .945
3.780 .787 .906 .906 .866 .945 .787 .945
4.094 .787 .906 .906 .866 .945 .787 .945
4.528 .866 .906 .906 .866 .945 .866 .945
CDX for GHFGR/L (25.4/31.7)-105-8
D GIF 8… GIFG 8… GDMY 8… GIPA 8… GIDA 8… GIA 8… GDMM 8CC…
4.134 .827 .906 .906 .906 .945 .827 .945
4.488 .866 .906 .906 .906 .945 .866 .945
4.961 .906 .906 .945 .906 .945 .906 .945
5.512-6.299 .945 .945 .945 .906 .945 .945 .945
CDX for GHFGR/L (25.4/31.7)-155-8
D GIF 8… GIFG 8… GDMY 8… GIPA 8… GIDA 8… GIA 8… GDMM 8CC…
6.102 .945 .945 .945 .906 .945 .945 .945
7.087 .945 .945 .945 .906 .945 .945 .945
8.268-20.079 .945 .945 .945 .906 .945 .945 .945

632 ISCAR