Page 122 - Turning_catalog_INCH_2022_45_P509-690
P. 122
FACE GROOVING GRIP Dimensions Tough 1 Hard BW Recommended Machining Data
INSL (Ref.)
±.004
Utility Double-Ended
RE
Inserts for External, Internal
and Face Machining
CW
No depth penetration limit
f face-
IC8250
f turn
f face-turn
groove
f groove
IC807
IC808
IC806
IC830
IC804
ap
IC08
RE
BW
CW
(IPR)
(IPR)
(IPR)
Designation
(inch)
(IPR)
.0020
.622
.00196
GRIP 3002Y
.091 • • • • • • • •
.118
.016-.071 .0059-.0075 .0027-.0043 .0031-.0079 .0039-.0079
GRIP 3003Y .118 CWTOL (1) .0079 RETOL (2) INSL .091 • • • • • IC908 IC418 IC5010 • • • .010-.071 .0055-.0071 .0027-.0043 .0031-.0079 .0039-.0079
.00196
.0020
.0118
.622
GRIP 318-040Y .125 .00196 .0157 .0020 .622 .091 • • • • • .020-.075 .0067-.0087 .0027-.0047 .0031-.0079 .0039-.0079
GRIP 4002Y .157 .00196 .0079 .0020 .748 .110 • • • • • • • .010-.094 .0063-.0083 .0035-.0055 .0039-.0094 .0059-.0118
GRIP 4004Y .157 .00196 .0157 .0020 .748 .110 • • • • • • • • • • .020-.094 .0071-.0094 .0035-.0059 .0039-.0094 .0059-.0118
GRIP 476-080Y .187 .00196 .0315 .0020 .748 .122 • • • • • • .039-.110 .0083-.0130 .0039-.0079 .0039-.0094 .0059-.0118
GRIP 5005Y .197 .00196 .0197 .0020 .748 .130 • • • • • • • • • • .024-.118 .0079-.0118 .0043-.0079 .0047-.0094 .0059-.0138
GRIP 5008Y .197 .00196 .0315 .0020 .748 .134 • • • • • • • • .039-.118 .0091-.0138 .0043-.0083 .0047-.0094 .0059-.0138
GRIP 6005Y .236 .00196 .0197 .0020 .748 .165 • • • • • • • • .024-.142 .0087-.0142 .0051-.0091 .0047-.0110 .0059-.0157
GRIP 6008Y .236 .00196 .0315 .0020 .748 .165 • • • • • • • • .039-.142 .0094-.0165 .0051-.0098 .0047-.0110 .0059-.0157
GRIP 635-080Y .250 .00196 .0315 .0020 .748 .165 • • • • • .039-.150 .0098-.0173 .0055-.0106 .0047-.0110 .0059-.0157
• For cutting speed recommendations and user guide, see pages 658-669
(1) Cutting width tolerance (+/-)
(2) Corner radius tolerance (+/-)
For tools, see pages: C#-HELIR/L (271) • C#-HFIR/L-MC (626) • CR HFIR-M (628) • D/HGAD RE/LE-JHP (553) • DGAD/HGAD (531)
• DGFH (275) • DGFH-JHP (276) • DGFS (520) • DGTR/L (525) • HELIIR/L (379) • HELIR/L (272) • HFAER/L-4 (622) • HFAER/L-5T, 6T (622)
• HFAIR/L-4 (624) • HFAIR/L-DG (625) • HFFR/L-T (619) • HFHR/L-4T (615) • HFHR/L-5T (615) • HFHR/L-6T (616) • HFIR/L-MC (627)
• HFPAD-3 (617) • HFPAD-4 (618) • HFPAD-5 (618) • HFPAD-6 (619) • HFPAD-JHP (617) • HGAER/L-3 (621) • HGAIR/L-3 (624) • HGFH (274)
• HGHR/L-3 (614) • HGPAD (274) • HGPAD-JHP (274) • IM-HFIR-MC (626)
The Twisted Insert
for Face Machining
The double-ended, twisted insert body
makes it possible to machine deeper
than the inserts’ length.
A unique chipformer for controlled chip
flow in axial and radial directions.
The rear angle is slanted in relation
to the frontal edge so it does not
come into contact with the machined
groove surface as the tool penetrates
deeply into the workpiece.
630 ISCAR