Page 88 - TURNING CATALOG p121-254

ISOTURN INSERTS WCGT 80° 93º
Trigon Inserts with a 7° L
Positive Flank and Chipformer
for Finish Turning RE 7°
IC S

Dimensions Tough 1 Hard Recommended Machining Data

IC908 ap f
IC30N
Designation L IC S RE (mm) (mm/rev)
••
WCGT 020102L 2.18 3.97 1.59 0.20 •• 0.40-2.00 0.05-0.10

WCGT 020104L 2.18 3.97 1.59 0.40 0.40-2.00 0.10-0.15

• For user guide and cutting speed recommendations, see pages 122-134, 236-248
For tools, see pages: A/E-SWUCR (119) • MG-SWUCR (119)

WPEX EPSR 90° 75° 60°
80° and 84° Precision
Trigon Inserts with Positive RE IC D1 45°
8° and 12° Clearance for AN°
Finishing Applications Dimensions Recommended
Machining Data
L S

Tough 1 Hard

IC08 ap f
IC908
Designation L S RE IC D1 EPSR AN (mm) (mm/rev)
8.0 •
WPEX 040200R/L08 4.00 2.50 0.00 6.60 3.20 84.0 12.0 • 0.20-2.00 0.05-0.20

WPEX 040200R12 4.00 2.50 0.00 6.60 3.20 84.0 8.0 • 0.20-2.00 0.05-0.20

WPEX 040202R/L08 4.00 2.50 0.20 6.60 3.20 84.0 0.20-2.00 0.05-0.20
8.0 • • 0.20-2.50 0.05-0.20
WPEX 050300R/L08 5.00 3.18 0.00 7.94 3.70 80.0 12.0 • • 0.20-2.50 0.05-0.20

WPEX 050300R12 5.00 3.18 0.00 7.94 3.70 80.0 8.0 • • 0.20-2.50 0.05-0.20

WPEX 050302R/L08 5.00 3.18 0.20 7.94 3.70 80.0 • 0.20-2.50 0.05-0.20

WPEX 050302R12 5.00 3.18 0.20 7.94 3.70 80.0 12.0
8.0 • • 0.20-2.50 0.05-0.20
WPEX 050304R/L08 5.00 3.18 0.40 7.94 3.70 80.0 • 0.20-2.50 0.05-0.20

WPEX 050304R12 5.00 3.18 0.40 7.94 3.70 80.0 12.0
8.0 • • 0.20-3.00 0.05-0.20
WPEX 060400R/L08 6.00 4.00 0.00 9.52 3.70 80.0 12.0 • • 0.20-3.00 0.05-0.20

WPEX 060400R/L12 6.00 4.00 0.00 9.52 3.70 80.0 8.0 • • 0.20-3.00 0.05-0.20

WPEX 060402R/L08 6.00 4.00 0.20 9.52 3.70 80.0 12.0 • • 0.20-3.00 0.05-0.20

WPEX 060402R/L12 6.00 4.00 0.20 9.52 3.70 80.0 8.0 • • 0.20-3.00 0.05-0.20

WPEX 060404R/L08 6.00 4.00 0.40 9.52 3.70 80.0 12.0 • • 0.20-3.00 0.05-0.20

WPEX 060404R12 6.00 4.00 0.40 9.52 3.70 80.0

• For user guide and cutting speed recommendations, see pages 122-134, 236-248

For tools, see pages: SWAPR-PAD (73) • SWAPR/L (73) • SWDPR/L (74)

CC95MT-SM 80° IC 95º
Single-Sided 80° Rhombic Inserts L D1 6.2 95º
for Finishing (CHAMELEON
Multifunction Pocket System) Dimensions RE S 95º

Tough 1 Hard Recommended
Machining Data

IC830 ap f
IC8250
RE IC8150
Designation L IC S 0.40 D1 (mm) (mm/rev)
•••
CC95MT 100504-SM 9.50 9.52 5.00 4.50 0.50-3.00 0.07-0.24

• For user guide and cutting speed recommendations, see pages 122-134, 236-248

For tools, see pages: S-SUXCR/L-CM (110) • SUXCR/L-CM (54)

208 ISCAR