Page 56 - ISCAR FACE GROOVING LINES
P. 56
FACE GROOVE-TURN LH
HFHR/L-M HF CDX H OAH
Toolholders for Shallow DAXN-DAXX OAW
Face Grooving
CWN-CWX B
CDX WF
OAL Right-hand shown
METRIC
Designation CWN(1) CWX(2) CDX WF H HF B OAL DAXN(3) DAXX(4) OAH OAW
2000.0 29.0 22.50
HFHR/L 20M 3.00 6.00 5.30 20.00 20.0 20.0 20.0 130.00 20.0 2000.0 34.0 27.50 SR M6X16 DIN912 HW 5.0
HFHR/L 25M 3.00 6.00 5.30 25.00 25.0 25.0 25.0 150.00 20.0 SR M6X16 DIN912 HW 5.0
• DGN & GRIP 4.. - 6.. inserts can be used only with right-hand tools, HGPL 4.. - 6.. inserts with left-hand tools
• After initial groove, no limitation to widening groove outward or toward center
• For user guide, see pages 161-173
(1) Minimum cutting width
(2) Maximum cutting width
(3) Minimum penetration diameter
(4) Maximum penetration diameter
For inserts, see pages: HFPR/L (68) • HFPR/L (full radius) (69)
HFHR/L- o M & HFHPR/L- o M CWX=6 mm Insert initial face grooving range
Integral Toolholders CWN=3 mm
DAXN-DAXX CW DAXN-DAXX
For shallow machining up to max. 5 mm depth of groove. DAXN-DAXX CW DAXN DAXX
One toolholder can be mounted with inserts in 3-6 mm 3 25.6 51.5
widths. The initial major diameter groove is limited by the 4 24.1 73.7
insert’s geometry of each size. 5 22.1 170
After the initial groove, face recessing outward or toward 6 20.8 ∞
the center is not limited by the insert’s geometry.
LH
HFHR/L-M H CDX H OAH
Toolholders for Shallow DAXN-DAXX OAW
Face Grooving
CWN-CWX B
CDX WF
OAL Right-hand shown
INCH
Designation CWN(1) CWX(2) CDX WF H B OAL LH DAXN(3) DAXX(4) OAH OAW
HFHR 19M 78.74 1.10 .850
HFHR/L 25.4M .118 .236 .209 .750 .750 .750 5.000 1.420 .79 78.74 1.35 1.100 SR M6X16 DIN912 HW 5.0
SR M6X16 DIN912 HW 5.0
.118 .236 .209 1.000 1.000 1.000 6.000 1.420 .79
• DGN & GRIP 4.. - 6.. inserts can be used only with right-hand tools, HGPL 4.. - 6.. inserts with left-hand tools
• After initial groove, no limitation to widening groove outward or toward center
• For user guide, see pages 161-173
(1) Minimum cutting width
(2) Maximum cutting width
(3) Minimum penetration diameter
(4) Maximum penetration diameter
For inserts, see pages: HFPR/L (68) • HFPR/L (full radius) (69)
HFHR/L-M & HFHPR/L-M CWX=.236” Insert initial face grooving range
CWN=.118”
Integral Toolholders DAXN-DAXX
For shallow machining to max. .209” depth of groove. DAXN-DAXX CW DAXX DAXN
One toolholder can be mounted with inserts in .118-.236” widths. DAXN-DAXX CW
The initial major diameter groove is limited by the insert geometry 2.362 .945 .117
in each size. 3.543 .906 .157
After initial groove, face recessing outward or toward 11.811 .827 .197
center is not limited by insert geometry. ∞ .787 .236
54 ISCAR
