Page 133 - MILLING CATALOG p319-550

RE W1 IC28 RE W1
IC882
HM90 APKT 1003 IC330APMX INSL APMX INSL Rd°
General Use Inserts with 2 IC328
Helical Cutting Edges for High IC830 Recommended
90° Shoulder Accuracy IC928 Machining Data
IC5400
BS BS IC950S
IC380
Dimensions IC808Tough 1 Hard
IC908
IC810apfz
IC910
Designation W1 INSL APMX S RE BS (mm) (mm/t)
MILLING INSERTS 0.08-0.15
HM90 APKT 1003PDR 6.76 11.45 8.00 3.53 0.80 1.40 • • • • • • • • • • • • 1.20-8.00 0.08-0.15
• 0.08-0.15
HM90 APKT 1003PDR-SC 6.80 11.60 8.00 4.00 0.40 1.80 • 0.80-8.00 0.08-0.20
0.08-0.15
HM90 APKT 1003PDR-MM 6.70 11.50 8.00 3.50 0.80 1.60 • 1.20-8.00 0.08-0.15
• 1.20-8.00 0.08-0.15
HM90 APKT 1003PDTR-8M 6.76 11.45 8.00 3.53 0.80 1.40 •• 0.08-0.15
6.76 11.45 8.00 3.53 0.40 1.78 • • 0.80-8.00 0.08-0.15
HM90 APKT 100304PDR •
0.08-0.15
HM90 APKT 100308R 6.76 11.45 8.00 3.53 0.80 1.00 •• 1.20-8.00
• 1.60-8.00
HM90 APKT 100312PDR 6.76 11.45 8.00 3.53 1.20 1.00 •• • 2.00-8.00

HM90 APKT 100316PDR 6.76 11.45 8.00 3.53 1.60 0.58 •• • 2.90-8.00

HM90 APKT 100325PDR 6.76 10.40 8.00 3.53 2.50 - •• • 3.40-8.00

HM90 APKT 100330PDR 6.76 10.40 8.00 3.53 3.00 -

• For inserts with corner radii larger than 1.5 mm, the cutter body should be modified • For cutting speed recommendations, see pages 542-547
For tools, see pages: HM90 E90A-10 (24) • HM90 E90A-M-10 (28) • HM90 E90A-MM-10 (27) • HM90 E90A-MM-10-JHP (27) • HM90 F90AP-10 (200) • HM90
F90AP-10-JHP (200)

HM90 APKT 1003PDTR-8M HM90 APKT 1003PDR HM90 APKT 1003PDR-MM HM90 APKT 1003PDR-SC

HM90 APKT 1003 - 8M HM90 APKT 1003 • Cutting edge geometry • Larger axial effective angle up to
• Super reinforced helical cutting edge • Helical cutting edge with high with low axial angle the middle of the insert length
• For interrupted cuts and
90˚ shoulder accuracy • Reinforced cutting edge • Reduced cutting forces, effective
heavy machining • Reduced mismatch - geometry, which provides up to 5 mm – the middle of
• Use for long overhang and extended better chipping resistance insert’s cutting edge length
improved surface quality
flute cutters with reduced chatter • For general use applications • Wide frontal wiper that leaves • Used for machining ductile high
excellent surface finish with low strength materials. Parts such
mismatch on the workpiece as shafts, gears, crankshafts,
connection rods, camshafts, etc.
• Used for unfavorable
conditions and high feeds

W1

HM90 APCR APMX lNSL
100304PDFR-P/DP
Inserts with Positive Helical BS RE S Rd°
Cutting Edges and Polished
Rake for Machining Aluminum Recommended
and High Temperature Alloys Machining Data

Dimensions Tough 1 Hard

IC28 ap fz
IC928
Designation W1 INSL APMX S RE BS IC08 (mm) (mm/t)
IC908

HM90 APCR 100304PDFR-P 6.52 11.25 8.00 3.85 0.40 1.52 •••• 0.80-8.00 0.07-0.25
HM90 APCR 100304PDFRDP 6.52 11.25 8.00 3.85 0.40 1.52 •
0.80-8.00 0.07-0.25

• Super positive peripherally ground chipformer • P - Polished rake DP- Polished rake and flank • Used for machining aluminum (fz 0.07-0.25), titanium (fz 0.05-0.08) and
magnesium (fz 0.05-0.10) • Recommended for coarse pitch cutters • For cutting speed recommendations, see pages 542-547
For tools, see pages: HM90 E90A-10 (24) • HM90 E90A-M-10 (28) • HM90 E90A-MM-10 (27) • HM90 E90A-MM-10-JHP (27) • HM90 F90AP-10 (200) • HM90

F90AP-10-JHP (200)

449